Nanostructures and metallophthalocyanines : applications in microbial fuel cells
- Authors: Edwards, Sean
- Date: 2011
- Subjects: Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4107 , http://hdl.handle.net/10962/d1011742 , Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Description: Microbial fuel cells (MFCs) are a promising form of alternative energy capable of harnessing the potential energy stores in organic waste. The oxygen reduction reaction (ORR) forms an integral role in the generation of electricity in MFCs however it is also a potential obstacle in enhancing the performance of MFCs. Platinum, a commonly used catalyst for the ORR, is expensive and rare. Significant research has been conducted into developing alternative catalysts. Metallophthalocyanines (MPc) have garnered attention for use as catalysts. Iron phthalocyanine (FePc) has been shown to have catalytic activity towards the reduction of oxygen. Coupling of the catalyst to nanostructured carbon materials, such as multi-walled carbon nanotubes, has been observed to have several advantages as nanostructures have a high surface-to-volume ratio. In this study, we have attempted to assess the suitability of FePc, both its bulk and nanostructured form, as an oxygen reduction catalyst and acid functionalized multi-walled carbon nanotubes for use as a catalyst support using electrochemical techniques such as cyclic voltammetry and electrochemical impedance spectroscopy. We showed, for the first time, the catalytic nature of nanostructured FePc towards the ORR. Applying the data obtained from the electrochemical analyses, electrodes were modified using FePc and MWCNTs and applied to an Enterobacter cloacae-based MFC. Several operational parameters of the MFC, such as temperature and ionic strength, were optimized during the course of the study. We showed that optimized FePc:MWCNT-modified electrodes compared favourably to platinum-based electrodes in terms of power densities obtained in a microbial fuel cell.
- Full Text:
Photophysical and photoelectrochemical properties of water soluble metallophthalocyanines
- Authors: Masilela, Nkosiphile
- Date: 2010
- Subjects: Phthalocyanines , Electrochemistry , Photoelectrochemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4330 , http://hdl.handle.net/10962/d1004991 , Phthalocyanines , Electrochemistry , Photoelectrochemistry
- Description: This work presents the synthesis, characterization, photophysicochemical and photoelectrochemical properties of anionic octa-caboxylated (MOCPcs), tetra-sulfonated (MTSPcs) and quaternized cationic (Q(T-2-Py)MPcs) water soluble aluminium, gallium, silicon, titanium and zinc phthalocynines. The peripherally tetra-substituted cationic (Q(T-2-Py)MPcs) and anionic (MTSPcs) were found to be aggregated in aqueous media, yet the octa-carboxylated (MOCPcs) counterparts were monomeric in solution. Cremophor EL (CEL) was used as a disaggregating agent, all the aggregated complexes disaggregated partially or completely in the presence of CEL. The photophysicochemical properties of aggregated complexes were investigated both in the presence of CEL and in aqueous media of pH 11 alone. Low triplet, singlet oxygen and fluorescence quantum yield were obtained in aqueous media (especially for the aggregated complexes) but a high improvement was achieved upon addition of CEL. The gallium complexes ((OH)GaOCPc and (OH)GaTSPc) showed good photophysicochemical properties with higher triplet and singlet oxygen quantum yields. For photoelectrochemistry the (MPcs) dyes were adsorbed to nanoporous ZnO, electrodeposited in the presence of eosin Y as structure directing agent (SDA) on FTO substrates by refluxing or soaking the films in a solution containing the dye of interest such that a full surface coverage was achieved. Quaternized cationic (Q(T-2-Py)MPc) and tetrasulfonated (MTSPcs) phthalocyanines formed strong aggregates when deposited on the surface of FTO/ZnO substrate leading. High external (IPCE) and internal (APCE) quantum efficiencies of up to 50.6% and 96.7% were achieved for the OTiOCPc complex. There was a lower overall cell efficiency for quaternized and tetrasulfonated metallophthalocyanines because of the strong aggregates when they were on the surface of the electrodes. Among the studied materials, OTiOCPc gave the highest overall cell efficiency of phthalocyanine electrodeposited on ZnO of so far = 0.48%.
- Full Text:
Electrochemical studies of titanium, manganese and cobalt phthalocyanines
- Authors: Nombona, Nolwazi
- Date: 2009
- Subjects: Titanium , Manganese , Cobalt , Phthalocyanines , Electrochemistry , Electrodes , Self-assembly (Chemistry)
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4312 , http://hdl.handle.net/10962/d1004970 , Titanium , Manganese , Cobalt , Phthalocyanines , Electrochemistry , Electrodes , Self-assembly (Chemistry)
- Description: Syntheses, spectral, electrochemical and spectroelectrochemical studies of phenylthio and amino derivatised metallophthalocyanines complexes are reported. The complexes are immobilized onto a gold macro disk, gold ultramicroelectrode and gold coated fiber electrodes via self assembly with phenylthio MPc derivatives or onto a glassy carbon electrode via electropolymerisation with amino MPc derivatives. For the first time MPc SAMs were formed on gold coated fiber. The electrocatalytic behavior of the modified electrodes was studied for the detection of nitrite and L-cysteine, all modified electrodes showed improved electrocatalytic oxidation compared to the unmodified electrode. The MPc complexes catalyzed nitrite oxidation via a two-electron mechanism producing nitrate. Cobalt tetraaminophthalocyanine showed the best catalytic activity for nitrite oxidation in terms of overpotential lowering compared to other complexes and thus was used for nitrite detection in a food sample, the nitrite concentration was determined to be 59.13 ppm, well within the limit for cured meat products. Electrocatalytic oxidation of L-cysteine on SAM modified gold coated fiber was reported for the first time. The gold coated fiber and ultamicro cylinder electrode were less stable towards the electro-oxidation of cysteine compared to its oxidation on the gold disk. The gold disk electrode gave better catalytic performance in terms of stability and reduction of overpotential. The phenylthio cobalt phthalocyanine derivative gave the best catalytic activity for L-cysteine oxidation in terms of overpotential lowering compared to other phenylthio derivatized MPc complexes. The amount of L-cysteine in human urine was 2.4 mM, well within the urinary L-cysteine excretion range for a healthy human being.
- Full Text:
Polymers, catalysts and nanostructures a hybrid approach to biomolecule detection
- Authors: Frith, Kelly-Anne
- Date: 2009
- Subjects: Polymers , Nanostructured materials , Biomolecules , Tryptophan , Melatonin , Electrodes , Electrochemistry , Tryptophan oxygenase
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:3980 , http://hdl.handle.net/10962/d1004039 , Polymers , Nanostructured materials , Biomolecules , Tryptophan , Melatonin , Electrodes , Electrochemistry , Tryptophan oxygenase
- Description: The main goals in electroanalytical sensing are towards improved sensitivity and selectivity, or specificity, of an analyte. There are several approaches to achieving these goals with the main approach being modification of an electrode surface with synthetic or natural catalysts (enzymes), polymers and also utilisation of nanostructured materials. At present, there is a strong movement towards hybrid sensing which couple different properties of two or more surface modification approaches. In this thesis, a range of these surface modifications were explored for analysis and detection of two main analytes: the amino acid, tryptophan (Trp); and, the neurotransmitter, dopamine (DA). Specifically, this thesis aimed to utilise these methods to enhance the sensitivity and selectivity for Trp over an interferent, the indoleamine, melatonin (Mel); and, DA over the vitamin, ascorbic acid (AA). For Trp detection, immobilisation of an enzyme, Tryptophanase (Trpase) resulted in poor selectivity for the analyte. However, enhanced sensitivity and selectivity was achieved through pH manipulation of the electrolyte medium at a Nafion®-modified electrode surface for both Trp and Mel. At pH 3.0, the Mel and Trp anodic peak potentials were sufficiently resolved allowing for an LOD of 1.60 and 1.62 nM,respectively, and permitting the accurate analysis of Trp in a dietary supplement containing Mel. Multi-walled carbon nanotubes (MWCNTs) suspended in Nafion® exhibited further increases in the signal responses of these analytes at pH 3.0 and 7.4 with minimal change in the resolution of the anodic peaks. A lower sensitivity was, therefore, observed at the Nafion® and MWCNT modified electrode compared to the Nafion®-modified electrode at pH 3.0 with LODs of 0.59 and 0.80 nM exhibited for Trp and Mel, respectively. Enhanced selectivity for Trp in the presence of Mel can be achieved with MWCNTs in the presence of metallotetrasulphonated phthalocyanines (MTSPcs) particularly at pH 3.0, owing to cation exchange effects. However, the lack of sensitivity towards Trp, and even Mel, at this CoTSPc and MWCNT modified electrode remains a drawback. For DA, detection at the MWCNT and Nafion® surface resulted in improved sensitivity over that of both the bare electrode (613.0 nM) and the Nafion® modified electrode (1045.1 nM) with a calculated LOD of 133.9 nM at this layer. Furthermore, improvements in the selectivity of DA were achieved at the Nafion® and MWCNT modified electrode as exclusion of AA (150 μM) was achieved. At the MWCNT and CoTSPc surface, AA was excluded up to 130 μM with sensitivity for DA extending as low as 14.3 nM, far greater than observed for Trp and Mel. These concentrations are well within physiological concentration ranges and represent the most significant solution yet in terms of AA exclusion and enhanced sensitivity for DA. An examination of the surface layering by impedance spectroscopy and atomic force microscopy indicates that the success of the hybrid sensor utilising CoTSPc and MWCNTs lay in improved dispersion of MWCNTs and improved electron transfer kinetics, facilitated by the net charge of the materials present. This thesis, thus, showed the utility of a judicious selection of synthetic and biological catalysts, polymers and carbon nanomaterials towards a hybrid approach to the electrochemical sensing of Trp, Mel, DA and AA with focus on sensitivity and selectivity of these analytes.
- Full Text:
Synthesis and electrochemistry of octapentylthio phthalocyanine complexes of manganese, titanium and vanadium
- Authors: Mbambisa, Gcineka
- Date: 2009
- Subjects: Electrochemistry , Phthalocyanines -- Synthesis , Manganese , Titanium , Vanadium
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4368 , http://hdl.handle.net/10962/d1005033 , Electrochemistry , Phthalocyanines -- Synthesis , Manganese , Titanium , Vanadium
- Description: Synthesis of new thio derivatised Pcs with manganese, titanium and vanadium as a central metal is reported. The complexes synthesised were characterised using spectroscopic and electrochemical means. The complexes displayed interesting spectroscopic properties with absorption of the Q band being observed in the near infrared region. These complexes have unusual colours for MPc complexes, with purple or red colour being observed in solution. Interesting electrochemical properties were observed, with rare observation of the MnIV/MnIII redox couple. There was observation of oxidation peaks for the pentylthio derivatised Pc with titanium as the central metal; this is unusual since for reported thio derivatives based on TiPc, no oxidation was observed. The vanadium based Pc showed an interesting spectrum for the first ring based reduction. The absorption spectrum obtained for the 1st reduction of the vanadium complex using spectroelectrochemistry would normally indicate a metal based process but comparing with literature it was concluded that it is a ring based reduction process. Generally all the MPc complexes formed a well ordered stable monolayer on the gold electrode. Electrocatalytic studies using L-cysteine revealed that the SAM based on manganese (III) octapentylthio phthalocyanine (AcOMnOPTPc) was the most effective since it catalyses L-cysteine at much lower oxidation potentials and it is also much more stable.
- Full Text:
Removal and photocatalysis of 4-Nitrophenol using metallophthalocyanines
- Authors: Marais, Eloïse Ann
- Date: 2008
- Subjects: Photocatalysis , Catalysis , Electrochemistry , Nitrophenols , Phthalocyanines
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4343 , http://hdl.handle.net/10962/d1005005 , Photocatalysis , Catalysis , Electrochemistry , Nitrophenols , Phthalocyanines
- Description: Photodegradation of 4-nitrophenol (4-Np) in the presence of water-soluble zinc phthalocyanines and water-insoluble metallophthalocyanines is reported. The water-soluble phthalocyanines employed include zinc tetrasulphophthalocyanine (ZnPcS[subscript 4]), zinc octacarboxyphthalocyanine (ZnPc(COOH)[subscript 8]) and a sulphonated ZnPc containing a mixture of differently sulphonated derivatives (ZnPcS[subscript mix]), while the water-insoluble phthalocyanines used include unsubstituted magnesium (MgPc), zinc (ZnPc) and chloroaluminium (ClAlPc) phthalocyanine complexes and the ring-substituted zinc tetranitro (ZnPc(NO[subscript 2])[subscript 4]), zinc tetraamino (ZnPc(NH[subscript 2])[subscript 4]), zinc hexadecafluoro (ZnPcF[subscript 16]) and zinc hexadecachloro (ZnPcCl[subscript 16]) phthalocyanines. The most effective water-soluble photocatalyst is ZnPcS[subscript mix] in terms of the high quantum yield obtained for 4-Np degradation (Φ[subscript 4-Np]) as well as its photostability. While ZnPc(COOH)[subscript 8] has the highest Φ[subscript 4-Np] value relative to the other water-soluble complexes, it degrades readily during photocatalysis. The Φ[subscript 4-Np] values were closely related to the singlet oxygen quantum yields Φ[subscript Δ] and hence aggregation. The rate constants for the reaction with 4-Np were kr = 0.67 x 10[superscript 6] mol[superscript -1] dm[superscript 3] s[superscript -1] for ZnPcS[subscript mix] and 7.7 x 10[superscript 6] mol[superscript -1] dm[superscript 3] s[superscript -1] for ZnPc(COOH)[subscript 8]. ClAlPc is the most effective photocatalyst relative to the other heterogeneous photocatalysts for the phototransformation of 4-Np, with 89 ± 8.4 % degradation of 4-Np achieved after 100 min. The least effective catalysts were ZnPcCl[subscript 16] and MgPc. The final products of the photocatalysis of 4-Np in the presence of the homogeneous photocatalysts include 4-nitrocatechol and hydroquinone, while degradation of 4-Np in the presence of the heterogeneous photocatalysts resulted in fumaric acid and 4-nitrocatechol. ClAlPc was employed for the heterogeneous photocatalysis of the non-systemic insecticide, methyl paraoxon. Complete degradation of the pesticide was confirmed by the disappearance of the HPLC trace for methyl paraoxon after 100 min of irradiation with visible light. The removal of 4-Np from an aqueous medium using commercially available Amberlite[superscript ®] IRA-900 modified with metal phthalocyanines was also investigated. The metallophthalocyanines immobilised onto the surface of Amberlite[superscript ®] IRA-900 include Fe (FePcS[subscript 4]), Co (CoPcS[subscript 4]) and Ni (NiPcS[subscript 4]) tetrasulphophthalocyanines, and differently sulphonated phthalocyanine mixtures of Fe (FePcS[subscript mix]), Co (CoPcS[subscript mix]) and Ni (NiPcS[subscript mix]). Adsorption rates were fastest for the modified adsorbents at pH 9. Using the Langmuir-Hinshelwood kinetic model, the complexes showed the following order of 4-Np adsorption: CoPcS[subscript mix] > NiPcS[subscript 4] > NiPcS[subscript mix] > FePcS[subscript 4] > FePcS[subscript mix] > CoPcS[subscript 4]. The adsorbents were regenerated using dilute HNO[subscript 3], with 76 % (7.6 x 10[superscript -5] mol) of 4-Np recovered within 150 min.
- Full Text:
Synthesis, photochemical and photophysical properties of gallium and indium phthalocyanine derivatives
- Authors: Chauke, Vongani Portia
- Date: 2008
- Subjects: Phthalocyanines , Photochemotherapy , Electrochemistry , Gallium , Indium
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4375 , http://hdl.handle.net/10962/d1005040 , Phthalocyanines , Photochemotherapy , Electrochemistry , Gallium , Indium
- Description: The syntheses of octasubstituted and unsusbstitituted Gallium(III) chloride and indium(III) chloride phthalocyanines (GaPc and InPc), their photophysical, photochemical and nonlinear optical parameters are hereby presented. The photocatalytic oxidation of 1-hexene using the synthesized GaPc and InPc complexes as well as electrochemical characterization is also presented in this thesis. Fluorescence quantum yields do not vary much among the four Ga complexes, except for complex 21c; therefore it was concluded that the effect of substituents is not significant among them. Solvents however, had an effect on the results. Lower Φ[subscript F] values were obtained in low viscosity solvents like toluene, relative to highly viscous solvents, such as DMSO. The triplet quantum yields were found to be lower in DMSO than in DMF and toluene. The rate constants for fluorescence, intersystem crossing and internal conversion as well as fluorescence and triplet lifetimes are reported. Photodegradation and singlet oxygen quantum yields have also been reported. There was no clear correlation between the latter parameters. It was however established that the four gallium MPcs were stable, within the allowed stability range for phthalocyanines. High quantum yields of triplet state (Φ[subscript T] ranging from 0.70 to 0.91 in dimethysulfoxide, DMSO) and singlet oxygen generation (Φ[subscript greek capital letter delta], ranging from 0.61 to 0.79 in DMSO) were obtained. Short triplet lifetimes 50 to 60 μs were obtained in DMSO). Calculated non-linear parameters of these complexes are compared with those of the corresponding GaPc derivatives and tetrasubstituted GaPc and InPc complexes. The optical limiting threshold intensity (I[subscript lim]) values for the InPc and GaPc derivatives were calculated and compared with those of corresponding tetrasubstituted InPc and GaPc complexes. The octasubstituted were found to be better optical limiters. Photocatalytic oxidation of 1-hexene by GaPc (21a-c) and InPc (22a-c) derivatives is also presented. The photocatalytic oxidation products for 1-hexene were 1,2- epoxyhexane and 1-hexen-3-ol. The % conversion values of 1-hexene and % selectivity of 1,2-epoxyhexane were generally higher for InPc derivatives. Even though InPc derivatives showed better photocatalytic results than GaPc derivatives, the former were less stable relative to the latter. Both type I and type II mechanism were implicated in the photocatalysis mechanism.
- Full Text:
Synthesis, photophysics and electrochemical study of tin macrocycles
- Authors: Khene, Mielie Samson
- Date: 2008
- Subjects: Electrochemistry , Photochemistry , Phthalocyanines , Macrocyclic compounds , Spectrum analysis
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4376 , http://hdl.handle.net/10962/d1005041 , Electrochemistry , Photochemistry , Phthalocyanines , Macrocyclic compounds , Spectrum analysis
- Description: Three non-peripherally substituted tin(IV) macrocylic compounds, octahexylphthalocyaninato dichlorotin(IV) (35a), octahexyltetrabenzo-5,10,15-triazaporphyrinato dichlorotin(IV) (35b) and octadecylphthalocyaninato dichlorotin(IV) (35c) were synthesized and their photophysical and electrochemical behaviour studied. Complex (35b), containing a CH group in place of one of the aza nitrogen atom of the phthalocyanine core, shows a split Q band due to its lower symmetry. The triplet state quantum yields were found to be lower than would be expected on the basis of the heavy atom effect of tin as the central metal for phthalocyanine derivatives (35a and 35c). In contrast, (35b) shows a triplet quantum yield ΦT = 0.78. The triplet state lifetimes were solvent dependent, and were higher in THF than in toluene. Cyclic voltammetry and spectroelectrochemistry of the complexes revealed only ring based redox processes. This thesis also reports on the microwave syntheses of tetrasulphonated tin phthalocyanine and tetrasulphonated tin α,β,γ-tetrabenzcorrole. The latter was only formed at low ratios (< 1:8) of 4-sulfophthalic acid to urea. Both complexes are aggregated in aqueous media, but can be partly or fully disaggregated by the addition of Triton X-100. The SnTSTBC complex has lower triplet life times and yields, while binding constant and quenching (of bovine serum albumin) constant are lower for SnTSTBC, compared to SnTSPc. Finally Non-peripherally (α) tetra- (40) and octa-(38a) substituted dodecyl-mercapto tin(IV) phthalocyanines where synthesized and the electrochemical behavior studied. Cyclic voltammetry and spectroelectrochemistry show ring-based reductions for (38a) and (40); the former shows two ring oxidations, while the latter shows only one ring based oxidation. The adsorption kinetics of (38a) and (40) on a gold electrode have been investigated by electrochemical impedance spectroscopy (EIS). The equilibrium constant (K) for the adsorption and the Gibbs free energy ΔG(ads) of the self-assembled monolayer (SAMs) were evaluated based on the Frumkin isotherm. The interaction factor between adsorbate –adsorbate molecules is also discussed.
- Full Text:
Study of metallophthalocyanines attached onto pre-modified gold surfaces
- Authors: Mashazi, Philani Nkosinathi
- Date: 2007
- Subjects: Phthalocyanines , Electrochemistry , Electrodes, Enzyme , Glucose -- Measurement
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4361 , http://hdl.handle.net/10962/d1005026 , Phthalocyanines , Electrochemistry , Electrodes, Enzyme , Glucose -- Measurement
- Description: Tetra-carboxy acid chloride phthalocyanine complexes of cobalt, iron and manganese were synthesized and characterized using spectroscopic and electrochemical techniques. These complexes were fabricated as thin films on gold electrode following a covalent immobilization and self-assembling methods. Surface electrochemical and spectroscopic characterization showed that these complexes are surface-confined species. The characterization using spectroscopic and electrochemical methods confirmed the formation of thiol and MPc SAMs on gold electrode. The electrocatalytic behaviour of the SAM modified gold electrodes was studied for the detection of L-cysteine and hydrogen peroxide. The limits of detection (LoD) for Lcysteine were of the orders of 10[superscript -7] mol.L[superscript -1] for all the MPc complexes studied and the LoD for hydrogen peroxide at cobalt phthalocyanine modified gold electrode was of the orders of 10[superscript -7]mol.L[superscript -1] for both electrocatalytic oxidation and reduction. The modification process for gold electrodes was reproducible and showed good stability, if stored in pH 4 phosphate buffer solutions and can be used over a long period of time. The cobalt phthalocyanine modified gold electrode was also investigated for the fabrication of glucose oxidase (GOx)-based biosensor and as an electron mediator between the enzyme and gold electrode. The behaviour of the enzyme modified gold electrode towards the detection of glucose was studied and the results gave a limit of detection of the orders of 10[superscript -6] mol.L[superscript -1] with low binding constant (4.8 mM) of enzyme (GOx) to substrate (glucose) referred to as Michaelis-Menten constant. The practical applications, i.e. the real sample analysis and interference studies, for the enzyme modified gold electrodes were investigated. These studies showed that the enzyme electrode is valuable and can be used for glucose detection.
- Full Text:
Substituted phthalocyanines development and self-assembled monolayer sensor studies
- Authors: Matemadombo, Fungisai
- Date: 2006
- Subjects: Phthalocyanines , Monomolecular films , Electrochemistry , Spectrum analysis
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4364 , http://hdl.handle.net/10962/d1005029 , Phthalocyanines , Monomolecular films , Electrochemistry , Spectrum analysis
- Description: Zinc, cobalt and iron phenylthio substituted phthalocyanines have been synthesized and characterized. Cyclic and square wave voltammetry in dimethylformamide containing tetrabutylammonium perchlorate revealed five and six redox processes respectively for the cobalt and iron phenylthio substituted phthalocyanines. These complexes are easier to reduce compared to the corresponding unsubstituted MPc and to butylthio substituted derivatives. Spectroelectrochemistry (in dimethylformamide containing tetrabutylammonium perchlorate) was employed to assign the cyclic voltammetry peaks, and gave spectra characteristic of Fe(I)Pc for reduction of iron phenylthio substituted phthalocyanine and Co(I)Pc for the reduction of cobalt phenylthio substituted phthalocyanine. The spectrum of the former is particularly of importance since such species have not received much attention in literature. Cobalt and iron phenylthio substituted phthalocyanines have been deposited on Au electrode surfaces through the self assembled monolayer (SAM) technique. The so formed layers were studied using voltammetric techniques. These SAMs blocked a number of Faradic processes and electrocatalyzed the oxidation of L-cysteine. Amine substituted cobalt phthalocyanine (CoTAPc) was deposited on gold surfaces by using an interconnecting SAM of mercaptopropionic acid or dithiobis(N-succinimidyl propionate) through the creation of an amide. Reductive and oxidative desorption of the SAMs limit the useful potential window. The SAM-CoTAPc layers show electrocatalytic activities towards oxygen reduction through the Co(I) central metal ion. Both SAMs were highly stable and hence will be interesting tools for further research in surface modification and sensor development.
- Full Text:
Synthesis of zinc phthalocyanine derivatives for possible use in photodynamic therapy
- Authors: Matlaba, Pulane Maseleka
- Date: 2003
- Subjects: Photochemotherapy , Electrochemistry , Phthalocyanines , Zinc
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4374 , http://hdl.handle.net/10962/d1005039 , Photochemotherapy , Electrochemistry , Phthalocyanines , Zinc
- Description: The synthesis of symmetrically and unsymmetrically substituted zinc phthalocyanines (ZnPc) derivatives is done according to reported procedures. The unsymmetrical ZnPc derivatives are synthesized by ring expansion of sub-phthalocyanine complexes. Ring substitution is effected with tert-butyl phenol, naphthol, and hydroxybenzoic acid. Comparison of the redox potentials for the complexes substituted with varying numbers of tert-butyl phenol: 1, 2, 3, 6 and 8 show that the complex with the highest number of substituents are more difficult to oxidize and easier to reduce. Water soluble sulphonated ZnPc (ZnPcSn) was prepared. The possibility of using axial ligation to increase the solubility and the photochemical activity of sulphotnated ZnPc in aqueous solutions was investigated. Pyridine, aminopyridyl and bipyridyl were used as axial ligands. When bipyridyl was used as the axial ligand, solubility of the ZnPcSn increased, shown by the increase in the Q-band of the monomer species in solution and the singlet oxygen quantum yields was relatively higher than that of the unligated ZnPcSn. The singlet oxygen quantum yields by the various complexes in DMF using diphenylisobenzofuran as a chemical quencher for organic solvent were determined. Singlet oxygen quantum yields for the unsymmetrically ring substituted complexes range from 0.22 to 0.68. Photobleaching quantum yields are in the order of 10-5, which means that the complexes are relatively photostable.
- Full Text:
Homogenous and heterogenous catalytic activity of metallophthalocyanines towards electrochemical detection of organic compounds
- Authors: Mafatle, Tsukutlane J P
- Date: 1998
- Subjects: Electrochemistry , Organic compounds , Phenols
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4316 , http://hdl.handle.net/10962/d1004974 , Electrochemistry , Organic compounds , Phenols
- Description: Cysteine plays an important role in many biological and pharmaceutical systems. Therefore, in view of its importance, it is essential to find means of detecting it at the lowest possible levels. In this regard, electrochemical techniques have been found to be capable of detecting analytes even at micro levels. However, electrochemical determination of cysteine occurs at a very high potentials. These overpotentials makes quantitative analysis or detection of cysteine difficult at most conventional carbon electrodes. On platinum electrode, the oxidation of cysteine has been reported to occur in the potential range 0.7 to 1.45 V (vs NHE). Therefore, the object of this investigative study has been to find an active complex that could replace platinum and other expensive metals as electrodes. Such a complex should also be capable of reducing the potential at which the oxidation of cysteine occurs on carbon electrodes. As a result, this manuscript gives a full report on the investigative study of electrocatalytic activity of molybdenum phthalocyanine complexes towards detection of cysteine. Molybdenum phthalocyanine, OMo(OH)Pc, and its tetrasulfonated derivative, [OMo(OH)TSPc]⁴⁻ were successfully used to reduce the potential needed to initiate the oxidation of cysteine on carbon paste electrodes (CPE). The oxidation of cysteine on CPE modified with [OMo(OH)Pc]⁴⁻ was found to occur at 0.29 V (vs Ag/AgCl), and in the presence of [OMo(OH)TSPc]⁴⁻ species in solution the oxidation occurred at 0.33 V (vs Ag/AgCl). Molybdenum, in the oxidation states of Mo(IV), Mo(V) and Mo(VI), is found in biological systems as an essential trace element, participating in a number of enzymatic reactions, where it is believed to be coordinated to sulphur-containing ligands in many molybdenum enzymes. This therefore explains why molybdenum phthalocyanines were employed in electroanalytical detection of sulphur containing amino acid, cysteine. Electrochemical methods have also been successfully used in detection of environmental pollutants such as phenolic compounds. Phenolic compounds are oxidised at readily accessible potentials. However, like cysteine, there are problems associated with the electrochemical detection of these important environmental pollutants. Their electrooxidation is known to form dimeric and/or polymeric oxidation products which adsorb onto the electrode surface, thus -videactivating it. Therefore, to address this problem, cobalt phthalocyanine (CoPc) and its tetrasulfonated derivative, [CoTSPc]⁴⁻ were employed in electrocatalytic detection of phenolic compounds. These complexes were found to increase the anodic peak currents for the oxidation of o-cresol, m-cresol, p-cresol, phenol, 2-chlorophenol and 4-chlorophenol. In addition, CoPc deposited onto the glassy carbon electrode improved the stability of the electrode, by reducing electrode poisoning caused by the electrooxidation products of the mentioned phenolic compounds. The potential at which the oxidation occurred and the current response of individual phenolic compounds depended on the degree of substitution and the type of substituent on the phenol molecule. In general, the current response was found to be lower for chlorinated phenols compared with the cresols and phenol. To establish the role of the central metal in the catalytic process, comparison of the electrocatalytic activity of some of the first row transition metal phthalocyanines, for the detection of mono-substituted phenolic compounds, showed the following trend: Co⁽¹¹⁾ > Mn⁽¹¹⁾ > Fe⁽¹¹⁾Pc > Ni⁽¹¹⁾Pc > Cu⁽¹¹⁾Pc > H₂Pc > Zn⁽¹¹⁾Pc > Bare GCE. A report is also given on electrocatalysis using [CoTSPc]⁴⁻ electrochemically deposited on the glassy carbon electrode. This was also found to enhance the anodic peak currents for the oxidation of all phenolic compounds. A report on the effects of scan rate, operating potential, analyte concentration and other variables is also given.
- Full Text:
Liquid junction potentials at mixed electrolyte salt bridges
- Authors: Finkelstein, Noel Phillip
- Date: 1957
- Subjects: Hydrogen-ion concentration -- Measurement , Hydrogen-ion concentration , Electrochemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4473 , http://hdl.handle.net/10962/d1011835 , Hydrogen-ion concentration -- Measurement , Hydrogen-ion concentration , Electrochemistry
- Description: The potentiometric method is one of the most exact techniques of electrochemistry. Its use is widespread in both routine measurements, such as pH determination, and in applications which demand the highest accuracy. Perhaps its severest limitation is the error due to liquid junction potentials. Although this has been the subject of much study, and although various means of combating it have been proposed, it has defied all attempts at a satisfactory solution. Indeed, so serious is the position that it has become the accepted practice in the more accurate fields to abandon altogether the use of potentiometric techniques in favour of others, usually less convenient and otherwise less accurate, when the presence of liquid junctions cannot be avoided. Intro. p. 1.
- Full Text: