Development of the Zirconium-based metal- organic framework UiO-66 for Adsorption-mediated electrochemical sensing of organonitrogen compounds in fuels
- Authors: Mokgohloa, Mathule Collen
- Date: 2024-04
- Subjects: Electrochemical sensors , Quinoline -- synthesis , Pyridine -- Synthesis
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10948/64193 , vital:73663
- Description: The combustion of fuel which contains organonitrogen compounds has led to an increase in atmospheric and environmental levels of nitrogen oxides which are responsible for several environmental, ecological, and human health problems. With increasingly strict environmental regulations and deleterious effects of the nitrogen-containing compounds in fuels, there is a strong need for the removal and detection of nitrogen-containing compounds in fuels to produce fuels with lower levels of nitrogen compounds. The Environmental Protection Agency (EPA) mandated nitrogen content in fossil fuels to be about less than 1 wt%. The existing analytical techniques used for the quantification of nitrogen-containing compounds in fuels include GC-MS, GC-AED, and spectrophotometry. Despite being sensitive and specific, these methods require expensive equipment, highly trained personnel, and time-consuming pre-treatment methods to avoid interferences from similar compounds, and they suffer from analyte loss and inadequate results. Thus, they can only be carried out in the off-site laboratories, hindering them from rapid on-site screening. The metal-organic framework (MOF) UiO-66-NH2 and its composites UiO-66-NH2/GA, and UiO- 66-NH2/GO-NH2 (GA= Graphene aerosol and GO= Graphene oxide) have shown great potentialin the adsorption of organonitrogen compounds like quinoline. However, research in the electrochemical application of these MOFs and their derivatives is limited despite their high surface area, abundant porosity, and increased conductivity. To demonstrate their electrochemical sensing potential, modification of the glassy carbon electrode (GCE) was suggested, which would show a higher degree of association for pyridine and quinoline on modified UiO-66-NH2/GA and UiO-66-NH2/GO-NH2 surfaces, thereby creating a more favourable route for adsorption. This would result in enhanced sensing of pyridine and quinoline in model fuel. Thus, unlike the bare GCE, the fabricated/modified can selectively detect high levels of organonitrogen compounds. In this study, Chapter 3, UiO-66-NH2/GA and UiO-66-NH2/GO-NH2 are prepared via the solvothermal method and then characterized using various spectroscopic and imaging techniques such as Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), Ultraviolet-Visible Spectroscopy (UV-VIS), Thermogravimetric Analysis (TGA), X-ray Development of the Zirconium-based metal- organic framework UiO-66 for Adsorption-mediated electrochemical sensing of organonitrogen compounds in fuels. , Thesis (MSc) -- Faculty of Science, School of Biomolecular & Chemical Sciences, 2024
- Full Text:
- Date Issued: 2024-04
- Authors: Mokgohloa, Mathule Collen
- Date: 2024-04
- Subjects: Electrochemical sensors , Quinoline -- synthesis , Pyridine -- Synthesis
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10948/64193 , vital:73663
- Description: The combustion of fuel which contains organonitrogen compounds has led to an increase in atmospheric and environmental levels of nitrogen oxides which are responsible for several environmental, ecological, and human health problems. With increasingly strict environmental regulations and deleterious effects of the nitrogen-containing compounds in fuels, there is a strong need for the removal and detection of nitrogen-containing compounds in fuels to produce fuels with lower levels of nitrogen compounds. The Environmental Protection Agency (EPA) mandated nitrogen content in fossil fuels to be about less than 1 wt%. The existing analytical techniques used for the quantification of nitrogen-containing compounds in fuels include GC-MS, GC-AED, and spectrophotometry. Despite being sensitive and specific, these methods require expensive equipment, highly trained personnel, and time-consuming pre-treatment methods to avoid interferences from similar compounds, and they suffer from analyte loss and inadequate results. Thus, they can only be carried out in the off-site laboratories, hindering them from rapid on-site screening. The metal-organic framework (MOF) UiO-66-NH2 and its composites UiO-66-NH2/GA, and UiO- 66-NH2/GO-NH2 (GA= Graphene aerosol and GO= Graphene oxide) have shown great potentialin the adsorption of organonitrogen compounds like quinoline. However, research in the electrochemical application of these MOFs and their derivatives is limited despite their high surface area, abundant porosity, and increased conductivity. To demonstrate their electrochemical sensing potential, modification of the glassy carbon electrode (GCE) was suggested, which would show a higher degree of association for pyridine and quinoline on modified UiO-66-NH2/GA and UiO-66-NH2/GO-NH2 surfaces, thereby creating a more favourable route for adsorption. This would result in enhanced sensing of pyridine and quinoline in model fuel. Thus, unlike the bare GCE, the fabricated/modified can selectively detect high levels of organonitrogen compounds. In this study, Chapter 3, UiO-66-NH2/GA and UiO-66-NH2/GO-NH2 are prepared via the solvothermal method and then characterized using various spectroscopic and imaging techniques such as Scanning Electron Microscopy (SEM), X-ray Photoelectron Spectroscopy (XPS), Ultraviolet-Visible Spectroscopy (UV-VIS), Thermogravimetric Analysis (TGA), X-ray Development of the Zirconium-based metal- organic framework UiO-66 for Adsorption-mediated electrochemical sensing of organonitrogen compounds in fuels. , Thesis (MSc) -- Faculty of Science, School of Biomolecular & Chemical Sciences, 2024
- Full Text:
- Date Issued: 2024-04
The systematic assembly of prostate specific antigen electrochemical sensors based on asymmetric Co(II) phthalocyanines, graphitic quantum dots and an aptamer
- Authors: Nxele, Siphesihle Robin
- Date: 2022-04-08
- Subjects: Prostate-specific antigen , Electrochemical sensors , Phthalocyanines , Quantum dots , Co(II) phthalocyanines , Aptamer
- Language: English
- Type: Doctoral thesis , text
- Identifier: http://hdl.handle.net/10962/232893 , vital:50035 , DOI 10.21504/10962/232893
- Description: The need for low-cost, efficient and simple diagnostic tools has led to more research going into this subject, with the aim of making such medical devices more accessible where they are needed. This has led to more researchers developing point-of-care devices for this purpose worldwide, by sensor fabrication. This thesis focuses on electrochemical sensor development for the early diagnosis of prostate cancer. It is common knowledge that prostate cancer is one of the most prevalent carcinomas that have claimed lives due to late diagnosis where even the most invasive treatments have failed. For this reason, development of early detection devices that can even be used in the comfort of home is necessary and quite crucial. Electrochemical sensors have gained much attention due to their ease of fabrication, cost effectiveness, simplicity, ease of use and high efficiency. Using nanocomposites as modifiers has also become popular as they provide greater stability and improve detection limits when used together with biomolecules. With that said, the work reported herein has combined nanocomposites of graphenebased quantum dots, gold nanoparticles, phthalocyanines and an aptamer in order to fabricate aptasensors for the electrochemical detection of prostate cancer biomarker. The aptamer is specifically designed to bind to the biomarker, and the nanocomposites are expected to enhance current output thus lowering detection limits and increasing stability and efficiency. Reproducible results are also expected. Prior to the detection of the prostate cancer biomarker, the quantum dots-phthalocyanine nanohybrids were used to detect L-cysteine, which is an amino acid, in order to verify the synergistic effects as electrode modifiers that lead to the enhancement of current output. This increase in current output is then v exploited for the improvement of aptasensor functionality upon incorporation of the aptamer, for the detection of prostate specific antigen. The research in this thesis has been carried out with the intention of contributing to the world of medical research, more so because of the ever-increasing need for medical care to become accessible to all and not only to those who can afford expensive technologies and treatments. , Thesis (PhD) -- Faculty of Science, Chemistry, 2022
- Full Text:
- Date Issued: 2022-04-08
- Authors: Nxele, Siphesihle Robin
- Date: 2022-04-08
- Subjects: Prostate-specific antigen , Electrochemical sensors , Phthalocyanines , Quantum dots , Co(II) phthalocyanines , Aptamer
- Language: English
- Type: Doctoral thesis , text
- Identifier: http://hdl.handle.net/10962/232893 , vital:50035 , DOI 10.21504/10962/232893
- Description: The need for low-cost, efficient and simple diagnostic tools has led to more research going into this subject, with the aim of making such medical devices more accessible where they are needed. This has led to more researchers developing point-of-care devices for this purpose worldwide, by sensor fabrication. This thesis focuses on electrochemical sensor development for the early diagnosis of prostate cancer. It is common knowledge that prostate cancer is one of the most prevalent carcinomas that have claimed lives due to late diagnosis where even the most invasive treatments have failed. For this reason, development of early detection devices that can even be used in the comfort of home is necessary and quite crucial. Electrochemical sensors have gained much attention due to their ease of fabrication, cost effectiveness, simplicity, ease of use and high efficiency. Using nanocomposites as modifiers has also become popular as they provide greater stability and improve detection limits when used together with biomolecules. With that said, the work reported herein has combined nanocomposites of graphenebased quantum dots, gold nanoparticles, phthalocyanines and an aptamer in order to fabricate aptasensors for the electrochemical detection of prostate cancer biomarker. The aptamer is specifically designed to bind to the biomarker, and the nanocomposites are expected to enhance current output thus lowering detection limits and increasing stability and efficiency. Reproducible results are also expected. Prior to the detection of the prostate cancer biomarker, the quantum dots-phthalocyanine nanohybrids were used to detect L-cysteine, which is an amino acid, in order to verify the synergistic effects as electrode modifiers that lead to the enhancement of current output. This increase in current output is then v exploited for the improvement of aptasensor functionality upon incorporation of the aptamer, for the detection of prostate specific antigen. The research in this thesis has been carried out with the intention of contributing to the world of medical research, more so because of the ever-increasing need for medical care to become accessible to all and not only to those who can afford expensive technologies and treatments. , Thesis (PhD) -- Faculty of Science, Chemistry, 2022
- Full Text:
- Date Issued: 2022-04-08
Design of pH Sensitive Electrochemical Sensor for Catecholamine Neurotransmitters Detection and the Screening Off of Ascorbic Acid
- Tshenkeng, Keamogetse Tebogo Charlotte
- Authors: Tshenkeng, Keamogetse Tebogo Charlotte
- Date: 2021-10-29
- Subjects: Catecholamines , Electrochemical sensors , Neurotransmitters , Vitamin C , Cobalt , Phthalocyanines , Cobalt (II) tetra-(3-carboxyphenoxy) phthalocyanine (CoTCPhOPc)
- Language: English
- Type: thesis , text
- Identifier: http://hdl.handle.net/10962/176921 , vital:42772
- Description: This study presents the synthesis of cobalt (II) tetra-(3-carboxyphenoxy) phthalocyanine (CoTCPhOPc) through the cyclotetramerization of 4-(3-carboxyphe-noxy)phthalonitrile and its full characterization using Fourier transform infrared (FT-IR) spectroscopy, ultraviolet-visible (UV-vis) spectroscopy, magnetic circular dichroism (MCD) spectroscopy, elemental analysis and mass spectrometry. The CoTCPhOPc was then immobilized onto phenylethylamino (PEA) pre-grafted gold electrode surface, Au-PEA using amide coupling reaction through a reaction with NHS and DCC to obtain Au-PEA-CoTCPhOPc. This yielded pH sensitive thin films due to the terminal carboxylic acid (–COOH) functional groups. Electrochemical and surface characterization was conducted to confirm the modification of the bare Au with PEA thin film (Au-PEA) and amide coupling of CoTCPhOPc (Au-PEA-CoTCPhOPc). The Au-PEA-CoTCPhOPc electrode was shown to possess pH selective properties towards negatively charged [Fe(CN)6]3-/4- and positively charged [Ru(NH3)6]2+/3+ redox probes. Au-PEA-CoTCPhOPc electrode surface enabled the detection of catecholamine neurotransmitters (dopamine, norepinephrine and epinephrine) and the screening off of ascorbic acid by means of pH sensitive functional groups. Bare Au and Au-PEA electrodes exhibited electro-oxidation and electroreduction of catecholamine neuro-transmitters and ascorbic acid at higher potentials compared to Au-PEA-CoTCPhOPc. There was no electro-oxidation or electroreduction of ascorbic acid at Au-PEA-CoTCPhOPc. For Au-PEA-CoTCPhOPc, excellent electrocatalytic oxidation with the limit of detection (LoD) determined using 3σ was found to be 1.32 (0.95), 2.11 (1.78) and 3.08 μM for electro-oxidation and electroreduction (in brackets) of dopamine, norepinephrine and epinephrine respectively. The limit of quantification (LoQ) was determined using 10σ and found to be 4.41 (3.17), 7.02 (5.93) and 10.3 μM electro-oxidation and electroreduction (in brackets) for dopamine, norepinephrine and epinephrine respectively. The Au-PEA-CoTCPhOPc thin film was shown to screen off ascorbic acid as no electrocatalytic oxidation was observed for up to 100.0 μM concentration. , Thesis (MSc) -- Faculty of Science, Department of Chemistry, 2021
- Full Text:
- Date Issued: 2021-10-29
- Authors: Tshenkeng, Keamogetse Tebogo Charlotte
- Date: 2021-10-29
- Subjects: Catecholamines , Electrochemical sensors , Neurotransmitters , Vitamin C , Cobalt , Phthalocyanines , Cobalt (II) tetra-(3-carboxyphenoxy) phthalocyanine (CoTCPhOPc)
- Language: English
- Type: thesis , text
- Identifier: http://hdl.handle.net/10962/176921 , vital:42772
- Description: This study presents the synthesis of cobalt (II) tetra-(3-carboxyphenoxy) phthalocyanine (CoTCPhOPc) through the cyclotetramerization of 4-(3-carboxyphe-noxy)phthalonitrile and its full characterization using Fourier transform infrared (FT-IR) spectroscopy, ultraviolet-visible (UV-vis) spectroscopy, magnetic circular dichroism (MCD) spectroscopy, elemental analysis and mass spectrometry. The CoTCPhOPc was then immobilized onto phenylethylamino (PEA) pre-grafted gold electrode surface, Au-PEA using amide coupling reaction through a reaction with NHS and DCC to obtain Au-PEA-CoTCPhOPc. This yielded pH sensitive thin films due to the terminal carboxylic acid (–COOH) functional groups. Electrochemical and surface characterization was conducted to confirm the modification of the bare Au with PEA thin film (Au-PEA) and amide coupling of CoTCPhOPc (Au-PEA-CoTCPhOPc). The Au-PEA-CoTCPhOPc electrode was shown to possess pH selective properties towards negatively charged [Fe(CN)6]3-/4- and positively charged [Ru(NH3)6]2+/3+ redox probes. Au-PEA-CoTCPhOPc electrode surface enabled the detection of catecholamine neurotransmitters (dopamine, norepinephrine and epinephrine) and the screening off of ascorbic acid by means of pH sensitive functional groups. Bare Au and Au-PEA electrodes exhibited electro-oxidation and electroreduction of catecholamine neuro-transmitters and ascorbic acid at higher potentials compared to Au-PEA-CoTCPhOPc. There was no electro-oxidation or electroreduction of ascorbic acid at Au-PEA-CoTCPhOPc. For Au-PEA-CoTCPhOPc, excellent electrocatalytic oxidation with the limit of detection (LoD) determined using 3σ was found to be 1.32 (0.95), 2.11 (1.78) and 3.08 μM for electro-oxidation and electroreduction (in brackets) of dopamine, norepinephrine and epinephrine respectively. The limit of quantification (LoQ) was determined using 10σ and found to be 4.41 (3.17), 7.02 (5.93) and 10.3 μM electro-oxidation and electroreduction (in brackets) for dopamine, norepinephrine and epinephrine respectively. The Au-PEA-CoTCPhOPc thin film was shown to screen off ascorbic acid as no electrocatalytic oxidation was observed for up to 100.0 μM concentration. , Thesis (MSc) -- Faculty of Science, Department of Chemistry, 2021
- Full Text:
- Date Issued: 2021-10-29
Characterisation of surfaces modified with phthalocyanines through click chemistry for applications in electrochemical sensing
- O'Donoghue, Charles St John Nqwabuko
- Authors: O'Donoghue, Charles St John Nqwabuko
- Date: 2018
- Subjects: Electrodes, Carbon , Phthalocyanines , X-ray photoelectron spectroscopy , Electrochemistry , Electrochemical sensors , Hydrazine , Click chemistry
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/58046 , vital:27038
- Description: One form of surface modification was primarily investigated in this work on glassy carbon electrodes. The form of modification is comprised of a series of steps in which electrografting is first applied to the glassy carbon surface, which is then followed up with click chemistry to ultimately immobilise a phthalocyanine onto the surface. The modified glassy carbon electrodes and surfaces were characterised with a combination of scanning electrochemical microscopy, X-ray photoelectron spectroscopy and various electrochemical methods. In this work, three alkyne substituted phthalocyanines were used. Two novel phthalocyanines, with nickel and cobalt metal centres, were studied alongside a manganese phthalocyanine reported in literature. Each of the three phthalocyanines was modified at the peripheral position with a 1-hexyne group, via a glycosidic bond, yielding the terminal alkyne groups that were used for subsequent click reactions. In situ diazotisation was used to graft 4-azidoaniline groups to the surface of the glassy carbon electrode. The azide bearing 4- azidoaniline groups were thus used to anchor the tetra substituted phthalocyanines to the surface of the electrodes. This method yielded successful modification of the electrodes and lead to their application in sensing studies. The modified electrodes were primarily used to catalyse the common agricultural oxidising agent hydrazine.
- Full Text:
- Date Issued: 2018
- Authors: O'Donoghue, Charles St John Nqwabuko
- Date: 2018
- Subjects: Electrodes, Carbon , Phthalocyanines , X-ray photoelectron spectroscopy , Electrochemistry , Electrochemical sensors , Hydrazine , Click chemistry
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/58046 , vital:27038
- Description: One form of surface modification was primarily investigated in this work on glassy carbon electrodes. The form of modification is comprised of a series of steps in which electrografting is first applied to the glassy carbon surface, which is then followed up with click chemistry to ultimately immobilise a phthalocyanine onto the surface. The modified glassy carbon electrodes and surfaces were characterised with a combination of scanning electrochemical microscopy, X-ray photoelectron spectroscopy and various electrochemical methods. In this work, three alkyne substituted phthalocyanines were used. Two novel phthalocyanines, with nickel and cobalt metal centres, were studied alongside a manganese phthalocyanine reported in literature. Each of the three phthalocyanines was modified at the peripheral position with a 1-hexyne group, via a glycosidic bond, yielding the terminal alkyne groups that were used for subsequent click reactions. In situ diazotisation was used to graft 4-azidoaniline groups to the surface of the glassy carbon electrode. The azide bearing 4- azidoaniline groups were thus used to anchor the tetra substituted phthalocyanines to the surface of the electrodes. This method yielded successful modification of the electrodes and lead to their application in sensing studies. The modified electrodes were primarily used to catalyse the common agricultural oxidising agent hydrazine.
- Full Text:
- Date Issued: 2018
Application of catalysts and nanomaterials in the design of an electrochemical sensor for ochratoxin A
- Authors: Flanagan, Shane Patrick
- Date: 2011 , 2010-12-06
- Subjects: Ochratoxins , Filamentous fungi , Electrochemical sensors , Nanostructured materials , Catalysts , Food contamination
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4121 , http://hdl.handle.net/10962/d1013328
- Description: Ochratoxin A is the most potent chlorinated derivative of the ochratoxin group, consisting of a 5'-chlorinated dihydroisocoumarin moiety linked by an amide bond to l-phenylalanine. Produced as a secondary fungal metabolite by several species of Aspergillus and Penicillium, ochratoxin A has been shown to readily contaminate a large variety of commodities including cereals, groundnuts, dried fruit, spices and coffee. This has led to widespread contamination of ochratoxin in wine, beer, milk and meat products. As ochratoxin A is a potent nephrotoxin exhibiting teratogenic and carcinogenic properties, the development of a rapid screening platform for the cost effective control of ochratoxin A content in foodstuffs is therefore required. The evaluation of metallophthalocyanine and carbon nanotube electrode modification toward the development of a nanostructured biosensor capable of enhancing the electrochemical detection of ochratoxin A in complex media is presented. Cyclic voltammetry at a glassy carbon electrode allowed for the optimization of detection parameters including pH and type of supporting electrolyte. Britton-Robinson buffer was found to be the most suitable supporting electrolyte in terms of sensitivity and reproducibility obtaining a LOD of 0.28 μM as determined by differential pulse voltammetry. Subsequent analysis determined the dependence of OTA oxidation on pH in acidic media which proceeds with the transfer of two electrons to form a quinone/hydroquinone couple shown to adsorb to the electrode surface. Passivation of the electrode through adsorption of oxidation products was shown to severely limit the detection of OTA upon successive detection cycles. Comparison of various metallophthalocyanine modifiers showed an increase in sensitivity toward the detection of OTA at phthalocyanine complexes with metal based redox processes. However with the exception of NiPc and CoTCPc complexes, phthalocyanine modification was limited by the increase in deviation of current response and extent of fouling. NiPc modification showed an increase in sensitivity by two fold with fouling characteristics comparable to an unmodified electrode while low improvements in fouling was observed at CoTCPc modified electrodes with sensitivity in detection comparable to an unmodified electrode.Modification of the electrode with multi- and single walled carbon nanotubes produced a significant increase in sensitivity toward the detection of ochratoxin A. The electrocatalytic activity of nanotube modifiers was attributed to the increase in surface area and to the addition of oxygenated functional groups upon acid treatment as confirmed by Raman spectroscopy. Acid functionalization of the carbon nanotubes for a period of two hours produced the greatest increase in sensitivity obtaining a respective LOD of 0.09 μM and 0.03 μM for analysis of ochratoxin A at multi- and single walled carbon nanotube modified electrodes. Centrifugal purification of carbon nanotubes was deemed necessary to improve the electrocatalytic activity of the nanotube modifiers through the removal of carbonaceous impurities as visualized by atomic force microscopy. Furthermore, a crude lipase preparation, lipase A, was investigated as a potential biological recognition element for selective detection of ochratoxin A in complex media. Lipase A enabled the hydrolysis of ochratoxin A to the electroactive species ochratoxin α as confirmed by thin layer chromatography and voltammetric analysis. Additional isolation of a pure hydrolase from the lipase A preparation is required prior to utilization within a nanostructured biosensor platform capable of detecting ochratoxin A in complex media.
- Full Text:
- Date Issued: 2011
- Authors: Flanagan, Shane Patrick
- Date: 2011 , 2010-12-06
- Subjects: Ochratoxins , Filamentous fungi , Electrochemical sensors , Nanostructured materials , Catalysts , Food contamination
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4121 , http://hdl.handle.net/10962/d1013328
- Description: Ochratoxin A is the most potent chlorinated derivative of the ochratoxin group, consisting of a 5'-chlorinated dihydroisocoumarin moiety linked by an amide bond to l-phenylalanine. Produced as a secondary fungal metabolite by several species of Aspergillus and Penicillium, ochratoxin A has been shown to readily contaminate a large variety of commodities including cereals, groundnuts, dried fruit, spices and coffee. This has led to widespread contamination of ochratoxin in wine, beer, milk and meat products. As ochratoxin A is a potent nephrotoxin exhibiting teratogenic and carcinogenic properties, the development of a rapid screening platform for the cost effective control of ochratoxin A content in foodstuffs is therefore required. The evaluation of metallophthalocyanine and carbon nanotube electrode modification toward the development of a nanostructured biosensor capable of enhancing the electrochemical detection of ochratoxin A in complex media is presented. Cyclic voltammetry at a glassy carbon electrode allowed for the optimization of detection parameters including pH and type of supporting electrolyte. Britton-Robinson buffer was found to be the most suitable supporting electrolyte in terms of sensitivity and reproducibility obtaining a LOD of 0.28 μM as determined by differential pulse voltammetry. Subsequent analysis determined the dependence of OTA oxidation on pH in acidic media which proceeds with the transfer of two electrons to form a quinone/hydroquinone couple shown to adsorb to the electrode surface. Passivation of the electrode through adsorption of oxidation products was shown to severely limit the detection of OTA upon successive detection cycles. Comparison of various metallophthalocyanine modifiers showed an increase in sensitivity toward the detection of OTA at phthalocyanine complexes with metal based redox processes. However with the exception of NiPc and CoTCPc complexes, phthalocyanine modification was limited by the increase in deviation of current response and extent of fouling. NiPc modification showed an increase in sensitivity by two fold with fouling characteristics comparable to an unmodified electrode while low improvements in fouling was observed at CoTCPc modified electrodes with sensitivity in detection comparable to an unmodified electrode.Modification of the electrode with multi- and single walled carbon nanotubes produced a significant increase in sensitivity toward the detection of ochratoxin A. The electrocatalytic activity of nanotube modifiers was attributed to the increase in surface area and to the addition of oxygenated functional groups upon acid treatment as confirmed by Raman spectroscopy. Acid functionalization of the carbon nanotubes for a period of two hours produced the greatest increase in sensitivity obtaining a respective LOD of 0.09 μM and 0.03 μM for analysis of ochratoxin A at multi- and single walled carbon nanotube modified electrodes. Centrifugal purification of carbon nanotubes was deemed necessary to improve the electrocatalytic activity of the nanotube modifiers through the removal of carbonaceous impurities as visualized by atomic force microscopy. Furthermore, a crude lipase preparation, lipase A, was investigated as a potential biological recognition element for selective detection of ochratoxin A in complex media. Lipase A enabled the hydrolysis of ochratoxin A to the electroactive species ochratoxin α as confirmed by thin layer chromatography and voltammetric analysis. Additional isolation of a pure hydrolase from the lipase A preparation is required prior to utilization within a nanostructured biosensor platform capable of detecting ochratoxin A in complex media.
- Full Text:
- Date Issued: 2011
- «
- ‹
- 1
- ›
- »