Electrospun fibre based colorimetric probes for biological molecules
- Authors: Mudabuka, Boitumelo
- Date: 2014
- Subjects: Nanofibers , Vitamin C , Dopamine
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4535 , http://hdl.handle.net/10962/d1016354
- Description: The thesis reports the use of electrospun nanofibres as a platform for the development of colorimetric probes. Three colorimetric probes in the form of electrospun nanofibre test strips were developed for the selective detection of ascorbic acid and dopamine because they are crucial biomolecules for physiological processes in human metabolism and usually coexist in biological samples. The simultaneous detection of the biomolecules is very important as their abnormal concentration levels would lead to diseases such as Parkinson's and schizophrenia. Different methods of incorporating detector agents into the nanofibre were exploited for the detection of the biomolecules. The methods included physical incorporation of nanoparticles, covalent bonding of ligand/dyes through surface modification of the fibres. The first colorimetric test strip for ascorbic acid was based on copper-gold alloy nanoparticles prepared in-situ and hosted in nylon6. The test strip showed selectivity in detecting ascorbic acid in the pH range 2 – 7. The suitability of fibres in hosting copper-gold alloy nanoparticles for the colorimetric detection of ascorbic acid was investigated using nylon6, poly(vinyl benzyl chloride)-styrene and cellulose acetate based test strips. All the test strips exhibited leaching and the nylon6 based test strip was found to be thermally stable up to 60 ˚C. The colorimetric performance of the test strips was maintained and neither was colour decay exhibited after 10 months of storage in a shelf. The test strip achieved an eye-ball limit of detection of 1.76 x10-2 mg L-1 and its suitability was demonstrated by the determination of ascorbic acid in fruit juices, urine, serum, and vitamin C tablets. The second colorimetric test strip for ascorbic acid and dopamine employed prussian blue synthesised in-situ in nylon6. Ascorbic acid turned the deep blue test strip to light blue at pH 3, and a faded navy blue colour at a pH range of 6 - 7 while dopamine changed the strip to purple at the same pH range. The versatility of the test strip was demonstrated by detecting ascorbic acid in commercial fruit juices as well as by detecting ascorbic acid as well as dopamine in fortified urine. The eye-ball detection limit of the Prussian blue test strip for ascorbic acid and dopamine was 17.6 mg L-1 and 18.9 mg L-1, respectively. The third method involved a covalent approach, where poly(vinylbenzyl chloride) nanofibers were post functionalised with 2-(2′-pyridyl)-imidazole and iron(III) for the selective detection of ascorbic acid and dopamine. The eye-ball detection limit for ascorbic acid and dopamine was 17.6 mg L-1 and 18.9 mg L-1, respectively. The test strip was selective for dopamine, but the detection of ascorbic acid suffered from interference by glutathione. The application of the test strips was nevertheless demonstrated by the detection of ascorbic acid in fruit juices and dopamine in fortified urine. The developed test strips employing the three approaches were applied without sample pre-treatment and use of supporting equipment.
- Full Text:
- Authors: Mudabuka, Boitumelo
- Date: 2014
- Subjects: Nanofibers , Vitamin C , Dopamine
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4535 , http://hdl.handle.net/10962/d1016354
- Description: The thesis reports the use of electrospun nanofibres as a platform for the development of colorimetric probes. Three colorimetric probes in the form of electrospun nanofibre test strips were developed for the selective detection of ascorbic acid and dopamine because they are crucial biomolecules for physiological processes in human metabolism and usually coexist in biological samples. The simultaneous detection of the biomolecules is very important as their abnormal concentration levels would lead to diseases such as Parkinson's and schizophrenia. Different methods of incorporating detector agents into the nanofibre were exploited for the detection of the biomolecules. The methods included physical incorporation of nanoparticles, covalent bonding of ligand/dyes through surface modification of the fibres. The first colorimetric test strip for ascorbic acid was based on copper-gold alloy nanoparticles prepared in-situ and hosted in nylon6. The test strip showed selectivity in detecting ascorbic acid in the pH range 2 – 7. The suitability of fibres in hosting copper-gold alloy nanoparticles for the colorimetric detection of ascorbic acid was investigated using nylon6, poly(vinyl benzyl chloride)-styrene and cellulose acetate based test strips. All the test strips exhibited leaching and the nylon6 based test strip was found to be thermally stable up to 60 ˚C. The colorimetric performance of the test strips was maintained and neither was colour decay exhibited after 10 months of storage in a shelf. The test strip achieved an eye-ball limit of detection of 1.76 x10-2 mg L-1 and its suitability was demonstrated by the determination of ascorbic acid in fruit juices, urine, serum, and vitamin C tablets. The second colorimetric test strip for ascorbic acid and dopamine employed prussian blue synthesised in-situ in nylon6. Ascorbic acid turned the deep blue test strip to light blue at pH 3, and a faded navy blue colour at a pH range of 6 - 7 while dopamine changed the strip to purple at the same pH range. The versatility of the test strip was demonstrated by detecting ascorbic acid in commercial fruit juices as well as by detecting ascorbic acid as well as dopamine in fortified urine. The eye-ball detection limit of the Prussian blue test strip for ascorbic acid and dopamine was 17.6 mg L-1 and 18.9 mg L-1, respectively. The third method involved a covalent approach, where poly(vinylbenzyl chloride) nanofibers were post functionalised with 2-(2′-pyridyl)-imidazole and iron(III) for the selective detection of ascorbic acid and dopamine. The eye-ball detection limit for ascorbic acid and dopamine was 17.6 mg L-1 and 18.9 mg L-1, respectively. The test strip was selective for dopamine, but the detection of ascorbic acid suffered from interference by glutathione. The application of the test strips was nevertheless demonstrated by the detection of ascorbic acid in fruit juices and dopamine in fortified urine. The developed test strips employing the three approaches were applied without sample pre-treatment and use of supporting equipment.
- Full Text:
Electrospun nanofibers as solid phase extraction sorbents and support for alkylphenols colorimetric probes
- Authors: Tancu, Yolanda
- Date: 2014
- Subjects: Nanofibers , Electrospinning , Extraction (Chemistry) , Sorbents , Phenols , Colorimetry , Transmission electron microscopy , High resolution spectroscopy
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4486 , http://hdl.handle.net/10962/d1012997
- Description: The thesis reports on fabricating alternative solid phase extraction (SPE) sorbents and colorimetric probes based on electrospun nanofibers for alkylphenols (APs). Hydroxyl methylated styrene [poly(co-styrene-CH₃OH)] and 3-oxobutanoate styrene [poly(co-styrene-OCOCH₃COCH₃)] copolymers were synthesized and fabricated into sorbent materials by electro-spinning/spraying. The fabricated morphologies consisting of bead free fibers, beaded fibers and particles were evaluated as SPE sorbents using batch experiments. Electropun fibers proved to be better sorbents as they exhibited extraction efficiency that exceeded 95% compared to 60% for beaded fibers and 40% for particles. In view to reduce sample and solvent volumes, smooth fibers were packed into pipette tips as SPE devices that yielded quantitative recoveries of APs from spiked wastewater samples. Recoveries ranged from 70% to 125% with LOD of 0.008, 0.01 and 0.1 μg mL⁻¹ for 4-tert octylphenol (4-t-OP), 4-octylphenol (4-OP) and 4-nonylphenol (4-NP) respectively, when using high performance liquid chromatography-fluorescence detector (HPLC-FLD). Furthermore, amino functionalised polydiacetylene polymers (PDAs), citrate capped gold (AuNPs) and silver nanoparticles (AgNPs) were evaluated as colorimetric probes for visual detection of APs. In colloidal studies, AuNPs probe showed a colour change from wine red to green upon introduction of analyte. UV-vis spectroscopy revealed the shifting of the surface plasmon resonance (SPR) peak from 525 nm to 729 nm induced by aggregation of AuNPs. For AgNPs probe, a colour change was observed from yellowish green to brown. Transmission electron microscopy (TEM) studies showed growth of AgNPs. A presumed oxidation of the analyte, forming an absorbing compound at 279 nm in both AgNPs and PDAs probes was also observed. For PDAs probe the colour change was from purple to pink. Concentrations as low as 30 μg mL⁻¹ were detectable in all colloidal based probes. Further colorimetric investigations were conducted with electrospun AuNPs-nylon 6 fiber mat. A colour change from purplish red to navy blue at concentrations of 1000 μg mL⁻¹ was observed. Electrospun AgNPs –nylon 6 fiber mat did not show a distinct colour change. High resolution scanning electron microscopy (HRSEM) revealed the analyte inducing the assembly of AuNPs and AgNPs as they covered the surface of the nanofiber mat. Electrospun nanofibers are a platform for analysis and thus tuning their chemistry will lead to sensitive and selective methods
- Full Text:
- Authors: Tancu, Yolanda
- Date: 2014
- Subjects: Nanofibers , Electrospinning , Extraction (Chemistry) , Sorbents , Phenols , Colorimetry , Transmission electron microscopy , High resolution spectroscopy
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4486 , http://hdl.handle.net/10962/d1012997
- Description: The thesis reports on fabricating alternative solid phase extraction (SPE) sorbents and colorimetric probes based on electrospun nanofibers for alkylphenols (APs). Hydroxyl methylated styrene [poly(co-styrene-CH₃OH)] and 3-oxobutanoate styrene [poly(co-styrene-OCOCH₃COCH₃)] copolymers were synthesized and fabricated into sorbent materials by electro-spinning/spraying. The fabricated morphologies consisting of bead free fibers, beaded fibers and particles were evaluated as SPE sorbents using batch experiments. Electropun fibers proved to be better sorbents as they exhibited extraction efficiency that exceeded 95% compared to 60% for beaded fibers and 40% for particles. In view to reduce sample and solvent volumes, smooth fibers were packed into pipette tips as SPE devices that yielded quantitative recoveries of APs from spiked wastewater samples. Recoveries ranged from 70% to 125% with LOD of 0.008, 0.01 and 0.1 μg mL⁻¹ for 4-tert octylphenol (4-t-OP), 4-octylphenol (4-OP) and 4-nonylphenol (4-NP) respectively, when using high performance liquid chromatography-fluorescence detector (HPLC-FLD). Furthermore, amino functionalised polydiacetylene polymers (PDAs), citrate capped gold (AuNPs) and silver nanoparticles (AgNPs) were evaluated as colorimetric probes for visual detection of APs. In colloidal studies, AuNPs probe showed a colour change from wine red to green upon introduction of analyte. UV-vis spectroscopy revealed the shifting of the surface plasmon resonance (SPR) peak from 525 nm to 729 nm induced by aggregation of AuNPs. For AgNPs probe, a colour change was observed from yellowish green to brown. Transmission electron microscopy (TEM) studies showed growth of AgNPs. A presumed oxidation of the analyte, forming an absorbing compound at 279 nm in both AgNPs and PDAs probes was also observed. For PDAs probe the colour change was from purple to pink. Concentrations as low as 30 μg mL⁻¹ were detectable in all colloidal based probes. Further colorimetric investigations were conducted with electrospun AuNPs-nylon 6 fiber mat. A colour change from purplish red to navy blue at concentrations of 1000 μg mL⁻¹ was observed. Electrospun AgNPs –nylon 6 fiber mat did not show a distinct colour change. High resolution scanning electron microscopy (HRSEM) revealed the analyte inducing the assembly of AuNPs and AgNPs as they covered the surface of the nanofiber mat. Electrospun nanofibers are a platform for analysis and thus tuning their chemistry will lead to sensitive and selective methods
- Full Text:
Oxidative desulfurization of fuel oils-catalytic oxidation and adsorptive removal of organosulfur compounds
- Authors: Ogunlaja, Adeniyi Sunday
- Date: 2014
- Subjects: Organosulfur compounds , Organosulfur compounds -- Oxidation , Organosulfur compounds -- Absorption and adsorption , Petroleum as fuel , Catalysis , Imprinted polymers , Molecular imprinting , Nanofibers , Electrospinning
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4498 , http://hdl.handle.net/10962/d1013152
- Description: The syntheses and evaluation of oxidovanadium(IV) complexes as catalysts for the oxidation of refractory organosulfur compounds in fuels is presented. The sulfones produced from the oxidation reaction were removed from fuel oils by employing molecularly imprinted polymers (MIPs). The oxidovanadium(IV) homogeneous catalyst, [V ͥ ͮ O(sal-HBPD)], as well as its heterogeneous polymer supported derivatives, poly[V ͥ ͮ O(sal-AHBPD)] and poly[V ͥ ͮ O(allylSB-co-EGDMA)], were synthesized and fully characterized by elemental analysis, FTIR, UV-Vis, XPS, AFM, SEM, BET and single crystal XRD for [V ͥ ͮ O(sal-HBPD)]. The MIPs were also characterized by elemental analysis, FTIR, SEM, EDX and BET. The catalyzed oxidation of fuel oil model sulfur compounds, thiophene (TH), benzothiophene (BT), dibenzothiophene (DBT) and 4,6-dimethyldibenzothiophene (4,6-DMDBT), was conducted under batch and continuous flow processes at 40°C by using tert-butylhydroperoxide (t-BuOOH) as oxidant. The continuous flow oxidation process presented the highest overall conversions and very high selectivity for sulfones. Maximum oxidation conversions of 71%, 89%, 99% and 88% was achieved for TH, BT, DBT and 4,6-DMDBT respectively when poly[V ͥ ͮ O(allylSB-co-EGDMA)] was employed at a flow-rate of 1 mL/h with over 90% sulfone selectivity. The process was further applied to the oxidation of hydro-treated diesel containing 385 ± 4.6 ppm of sulfur (mainly dibenzothiophene and dibenzothiophene derivatives), and this resulted to a high sulfur oxidation yield (> 99%), thus producing polar sulfones which are extractible by polar solid phase extractants. Adsorption of the polar sulfone compounds was carried-out by employing MIPs which were fabricated through the formation of recognition sites complementary to oxidized sulfur-containing compounds (sulfones) on electrospun polybenzimidazole (PBI) nanofibers, cross-linked chitosan microspheres and electrospun chitosan nanofibers. Adsorption of benzothiophene sulfone (BTO₂), dibenzothiophene sulfone (DBTO₂) and 4,6-dimethyldibenzothiophene sulfone (4,6-DMDBTO₂) on the various molecularly imprinted adsorbents presented a Freundlich (multi-layered) adsorption isotherm which indicated interaction of adsorbed organosulfur compounds. Maximum adsorption observed for BTO₂, DBTO₂ and 4,6-DMDBTO₂ respectively was 8.5 ± 0.6 mg/g, 7.0 ± 0.5 mg/g and 6.6 ± 0.7 mg/g when imprinted chitosan nanofibers were employed, 4.9 ± 0.5 mg/g, 4.2 ± 0.7 mg/g and 3.9 ± 0.6 mg/g on molecularly imprinted chitosan microspheres, and 28.5 ± 0.4 mg/g, 29.8 ± 2.2 mg/g and 20.1 ± 1.4 mg/g on molecularly imprinted PBI nanofibers. Application of electrospun chitosan nanofibers on oxidized hydro-treated diesel presented a sulfur removal capacity of 84%, leaving 62 ± 3.2 ppm S in the fuel, while imprinted PBI electrospun nanofibers displayed excellent sulfur removal, keeping sulfur in the fuel after the oxidation/adsorption below the determined limit of detection (LOD), which is 2.4 ppm S. The high level of sulfur removal displayed by imprinted PBI nanofibers was ascribed to hydrogen bonding effects, and π-π stacking between aromatic sulfone compounds and the benzimidazole ring which were confirmed by chemical modelling with density functional theory (DFT) as well as the imprinting effect. The home-made pressurized hot water extraction (PHWE) system was applied for extraction/desorption of sulfone compounds adsorbed on the PBI nanofibers at a flow rate of 1 mL/min and at 150°C with an applied pressure of 30 bars. Application of molecularly imprinted PBI nanofibers for the desulfurization of oxidized hydro-treated fuel showed potential for use in refining industries to reach ultra-low sulfur fuel level, which falls below the 10 ppm sulfur limit which is mandated by the environmental protection agency (EPA) from 2015.
- Full Text:
- Authors: Ogunlaja, Adeniyi Sunday
- Date: 2014
- Subjects: Organosulfur compounds , Organosulfur compounds -- Oxidation , Organosulfur compounds -- Absorption and adsorption , Petroleum as fuel , Catalysis , Imprinted polymers , Molecular imprinting , Nanofibers , Electrospinning
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4498 , http://hdl.handle.net/10962/d1013152
- Description: The syntheses and evaluation of oxidovanadium(IV) complexes as catalysts for the oxidation of refractory organosulfur compounds in fuels is presented. The sulfones produced from the oxidation reaction were removed from fuel oils by employing molecularly imprinted polymers (MIPs). The oxidovanadium(IV) homogeneous catalyst, [V ͥ ͮ O(sal-HBPD)], as well as its heterogeneous polymer supported derivatives, poly[V ͥ ͮ O(sal-AHBPD)] and poly[V ͥ ͮ O(allylSB-co-EGDMA)], were synthesized and fully characterized by elemental analysis, FTIR, UV-Vis, XPS, AFM, SEM, BET and single crystal XRD for [V ͥ ͮ O(sal-HBPD)]. The MIPs were also characterized by elemental analysis, FTIR, SEM, EDX and BET. The catalyzed oxidation of fuel oil model sulfur compounds, thiophene (TH), benzothiophene (BT), dibenzothiophene (DBT) and 4,6-dimethyldibenzothiophene (4,6-DMDBT), was conducted under batch and continuous flow processes at 40°C by using tert-butylhydroperoxide (t-BuOOH) as oxidant. The continuous flow oxidation process presented the highest overall conversions and very high selectivity for sulfones. Maximum oxidation conversions of 71%, 89%, 99% and 88% was achieved for TH, BT, DBT and 4,6-DMDBT respectively when poly[V ͥ ͮ O(allylSB-co-EGDMA)] was employed at a flow-rate of 1 mL/h with over 90% sulfone selectivity. The process was further applied to the oxidation of hydro-treated diesel containing 385 ± 4.6 ppm of sulfur (mainly dibenzothiophene and dibenzothiophene derivatives), and this resulted to a high sulfur oxidation yield (> 99%), thus producing polar sulfones which are extractible by polar solid phase extractants. Adsorption of the polar sulfone compounds was carried-out by employing MIPs which were fabricated through the formation of recognition sites complementary to oxidized sulfur-containing compounds (sulfones) on electrospun polybenzimidazole (PBI) nanofibers, cross-linked chitosan microspheres and electrospun chitosan nanofibers. Adsorption of benzothiophene sulfone (BTO₂), dibenzothiophene sulfone (DBTO₂) and 4,6-dimethyldibenzothiophene sulfone (4,6-DMDBTO₂) on the various molecularly imprinted adsorbents presented a Freundlich (multi-layered) adsorption isotherm which indicated interaction of adsorbed organosulfur compounds. Maximum adsorption observed for BTO₂, DBTO₂ and 4,6-DMDBTO₂ respectively was 8.5 ± 0.6 mg/g, 7.0 ± 0.5 mg/g and 6.6 ± 0.7 mg/g when imprinted chitosan nanofibers were employed, 4.9 ± 0.5 mg/g, 4.2 ± 0.7 mg/g and 3.9 ± 0.6 mg/g on molecularly imprinted chitosan microspheres, and 28.5 ± 0.4 mg/g, 29.8 ± 2.2 mg/g and 20.1 ± 1.4 mg/g on molecularly imprinted PBI nanofibers. Application of electrospun chitosan nanofibers on oxidized hydro-treated diesel presented a sulfur removal capacity of 84%, leaving 62 ± 3.2 ppm S in the fuel, while imprinted PBI electrospun nanofibers displayed excellent sulfur removal, keeping sulfur in the fuel after the oxidation/adsorption below the determined limit of detection (LOD), which is 2.4 ppm S. The high level of sulfur removal displayed by imprinted PBI nanofibers was ascribed to hydrogen bonding effects, and π-π stacking between aromatic sulfone compounds and the benzimidazole ring which were confirmed by chemical modelling with density functional theory (DFT) as well as the imprinting effect. The home-made pressurized hot water extraction (PHWE) system was applied for extraction/desorption of sulfone compounds adsorbed on the PBI nanofibers at a flow rate of 1 mL/min and at 150°C with an applied pressure of 30 bars. Application of molecularly imprinted PBI nanofibers for the desulfurization of oxidized hydro-treated fuel showed potential for use in refining industries to reach ultra-low sulfur fuel level, which falls below the 10 ppm sulfur limit which is mandated by the environmental protection agency (EPA) from 2015.
- Full Text:
The development of functionalized electrospun nanofibers for the control of pathogenic microorganisms in water.
- Authors: Kleyi, Phumelele Eldridge
- Date: 2014
- Subjects: Electrospinning , Nanofibers , Pathogenic microorganisms , Pathogenic microorganisms -- Detection , Drinking water -- Microbiology , Water quality -- Measurement , Imidazoles , Spectrum analysis , Anti-infective agents , Polymerization
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4497 , http://hdl.handle.net/10962/d1013134
- Description: The thesis presents the development of functionalized electrospun nylon 6 nanofibers for the eradication of pathogenic microorganisms in drinking water. Imidazole derivatives were synthesized as the antimicrobial agents and were characterized by means of NMR spectroscopy, IR spectroscopy, elemental analysis and X-ray crystallography. The first set of compounds (2-substituted N-alkylimidazoles) consisted of imidazole derivatives substituted with different alkyl groups (methyl, ethyl, propyl, butyl, heptyl, octyl, decyl and benzyl) at the 1-position and various functional groups [carboxaldehyde (CHO), alcohol (CH2OH) and carboxylic acid (COOH)] at the 2-position. It was observed that the antimicrobial activity of the compounds increased with increasing alkyl chain length and decreasing pKa of the 2-substituent. It was also observed that the antimicrobial activity was predominantly against a Gram-positive bacterial strains [Staphylococcus aureus (MIC = 5-160 μg/mL) and Bacillus subtilis subsp. spizizenii (MIC = 5-20 μg/mL)], with the latter being the more susceptible. However, the compounds displayed poor antimicrobial activity against Gram-negative bacterial strain, E. coli (MIC = 150- >2500 μg/mL) and did not show any activity against the yeast, C. albicans. The second set of compounds consisted of the silver(I) complexes containing 2-hydroxymethyl-N-alkylimidazoles. The complexes displayed a broad spectrum antimicrobial activity towards the microorganisms that were tested and their activity [E. coli (MIC = 5-40 μg/mL), S. aureus (MIC = 20-80 μg/mL), Bacillus subtilis subsp. spizizenii (MIC = 5-40 μg/mL) and C. albicans (MIC = 40-80 μg/mL)] increased with the alkyl chain length of the 2-hydroxymethyl-N-alkylimidazole. The third set of compounds consisted of the vinylimidazoles containing the vinyl group either at the 1-position or at the 4- or 5- position. The imidazoles with the vinyl group at the 4- or 5-position contained the alkyl group (decyl) at the 1-position. For the fabrication of the antimicrobial nanofibers, the first two sets of imidazole derivatives (2-substituted N-alkylimidazoles and silver(I) complexes) were incorporated into electrospun nylon 6 nanofibers while the third set (2-substituted vinylimidazoles) was immobilized onto electrospun nylon 6 nanofibers employing the graft polymerization method. The antimicrobial nylon nanofibers were characterized by IR spectroscopy and SEM-EDAX (EDS). The electrospun nylon 6 nanofibers incorporated with 2-substituted N-alkylimidazoles displayed moderate to excellent levels of growth reduction against S. aureus (73.2-99.8 percent). For the electrospun nylon 6 nanofibers incorporated with silver(I) complexes, the levels of growth reduction were >99.99 percent, after the antimicrobial activity evaluation using the shake flask method. Furthermore, the grafted electrospun nylon 6 nanofibers showed excellent levels of growth reduction for E. coli (99.94-99.99 percent) and S. aureus (99.93-99.99 percent). The reusability results indicated that the grafted electrospun nylon 6 nanofibers maintained the antibacterial activity until the third cycle of useage. The cytotoxicity studies showed that grafted electrospun nylon 6 nanofibers possess lower cytotoxic effects on Chang liver cells with IC50 values in the range 23.48-26.81 μg/mL. The thesis demonstrated that the development of antimicrobial electrospun nanofibers, with potential for the eradication of pathogenic microoganisms in water, could be accomplished by incorporation as well as immobilization strategies.
- Full Text:
- Authors: Kleyi, Phumelele Eldridge
- Date: 2014
- Subjects: Electrospinning , Nanofibers , Pathogenic microorganisms , Pathogenic microorganisms -- Detection , Drinking water -- Microbiology , Water quality -- Measurement , Imidazoles , Spectrum analysis , Anti-infective agents , Polymerization
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4497 , http://hdl.handle.net/10962/d1013134
- Description: The thesis presents the development of functionalized electrospun nylon 6 nanofibers for the eradication of pathogenic microorganisms in drinking water. Imidazole derivatives were synthesized as the antimicrobial agents and were characterized by means of NMR spectroscopy, IR spectroscopy, elemental analysis and X-ray crystallography. The first set of compounds (2-substituted N-alkylimidazoles) consisted of imidazole derivatives substituted with different alkyl groups (methyl, ethyl, propyl, butyl, heptyl, octyl, decyl and benzyl) at the 1-position and various functional groups [carboxaldehyde (CHO), alcohol (CH2OH) and carboxylic acid (COOH)] at the 2-position. It was observed that the antimicrobial activity of the compounds increased with increasing alkyl chain length and decreasing pKa of the 2-substituent. It was also observed that the antimicrobial activity was predominantly against a Gram-positive bacterial strains [Staphylococcus aureus (MIC = 5-160 μg/mL) and Bacillus subtilis subsp. spizizenii (MIC = 5-20 μg/mL)], with the latter being the more susceptible. However, the compounds displayed poor antimicrobial activity against Gram-negative bacterial strain, E. coli (MIC = 150- >2500 μg/mL) and did not show any activity against the yeast, C. albicans. The second set of compounds consisted of the silver(I) complexes containing 2-hydroxymethyl-N-alkylimidazoles. The complexes displayed a broad spectrum antimicrobial activity towards the microorganisms that were tested and their activity [E. coli (MIC = 5-40 μg/mL), S. aureus (MIC = 20-80 μg/mL), Bacillus subtilis subsp. spizizenii (MIC = 5-40 μg/mL) and C. albicans (MIC = 40-80 μg/mL)] increased with the alkyl chain length of the 2-hydroxymethyl-N-alkylimidazole. The third set of compounds consisted of the vinylimidazoles containing the vinyl group either at the 1-position or at the 4- or 5- position. The imidazoles with the vinyl group at the 4- or 5-position contained the alkyl group (decyl) at the 1-position. For the fabrication of the antimicrobial nanofibers, the first two sets of imidazole derivatives (2-substituted N-alkylimidazoles and silver(I) complexes) were incorporated into electrospun nylon 6 nanofibers while the third set (2-substituted vinylimidazoles) was immobilized onto electrospun nylon 6 nanofibers employing the graft polymerization method. The antimicrobial nylon nanofibers were characterized by IR spectroscopy and SEM-EDAX (EDS). The electrospun nylon 6 nanofibers incorporated with 2-substituted N-alkylimidazoles displayed moderate to excellent levels of growth reduction against S. aureus (73.2-99.8 percent). For the electrospun nylon 6 nanofibers incorporated with silver(I) complexes, the levels of growth reduction were >99.99 percent, after the antimicrobial activity evaluation using the shake flask method. Furthermore, the grafted electrospun nylon 6 nanofibers showed excellent levels of growth reduction for E. coli (99.94-99.99 percent) and S. aureus (99.93-99.99 percent). The reusability results indicated that the grafted electrospun nylon 6 nanofibers maintained the antibacterial activity until the third cycle of useage. The cytotoxicity studies showed that grafted electrospun nylon 6 nanofibers possess lower cytotoxic effects on Chang liver cells with IC50 values in the range 23.48-26.81 μg/mL. The thesis demonstrated that the development of antimicrobial electrospun nanofibers, with potential for the eradication of pathogenic microoganisms in water, could be accomplished by incorporation as well as immobilization strategies.
- Full Text:
A study of electrospun nanofibers and diatomaceous earth materials for the extraction of alkaloids, flavonoids and aromatic amines in various matrices
- Mothibedi, Kediemetse (Kedimetse)
- Authors: Mothibedi, Kediemetse (Kedimetse)
- Date: 2013 , 2013-04-07
- Subjects: Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4288 , http://hdl.handle.net/10962/d1003052 , Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Description: The thesis explored the use of different sorbent materials in solid phase extraction method development. The methods included the use of the polymeric Agilent Bond Elut Plexa solid phase extraction and electrospun polymer-silica composite sorbents for clean-up and preconcentration. Sample clean-up for alkaloids (hydrastine and berberine) in goldenseal, Hydrastis canadensis and flavonoids (quercetin, kaempferol and isorhamnetin) in Ginkgo biloba was achieved using Bond Elut Plexa SPE sorbent. Clean-up of flavonoids in Ginkgo biloba was also achieved using electrospun polymer-silica composite (polystyrene-silica, polyacrylonitrile-silica and nylon 6-silica) sorbents. All analysis of flavonoids and alkaloids was carried out using an Agilent 1200 Series HPLC coupled with a diode array detector. Good peak separation was achieved in less than 6 min employing an Agilent ZORBAX Eclipse Plus C18 column (4.6 x 75 mm, 3.5 μm) at 35⁰C. The mobile phases employed were 0.1% phosphoric acid/methanol gradient and 0.5% phosphoric acid/methanol (40:60) for alkaloids and flavonoids respectively. The calibration curves exhibited linearity up to 120 μg mL⁻¹ with correlation coefficients of more than 0.9980. The recoveries ranged from 73-109% with relative standard deviation of less than 5% for all analytes. Agilent Chem Elut supported liquid extraction was employed for the development of a sample preparation method for the determination of 24 banned aromatic amines from azo dyes in textile following the EU standard method EN 14362-1:2003 (E) and the Chinese standard method GB/T 17592-2006. The supported liquid extraction was effective in the extraction of the aromatic amines from textile (cotton, wool and polyester/cotton [80%:20%]). Most of the recoveries obtained were conforming to the minimum requirements set in the EN 14362-1:2003 (E) standard method and the relative standard deviations were less than 15%. Good peak separation was obtained within 70 min run time using the Agilent Zorbax SB-Phenyl column (4.6 mm x 250 mm, 5-micron) or the Agilent DB-35 MS (J & W) (30 m x 0.25 mm, 0.25 μm film thickness. It was demonstrated that the polymeric Agilent Bond Elut Plexa, electrospun nanofibers and diatomaceous earth were effective in extraction of alkaloids, flavonoids and aromatic amines in different matrices. The developed methods were simple, rapid and reproducible.
- Full Text:
- Authors: Mothibedi, Kediemetse (Kedimetse)
- Date: 2013 , 2013-04-07
- Subjects: Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4288 , http://hdl.handle.net/10962/d1003052 , Nanofibers , Electrospinning , Sorbents , Extraction (Chemistry) , Alkaloids , Flavonoids , Amines , Matrices , Goldenseal , Ginkgo , Dyes and dyeing -- Chemistry
- Description: The thesis explored the use of different sorbent materials in solid phase extraction method development. The methods included the use of the polymeric Agilent Bond Elut Plexa solid phase extraction and electrospun polymer-silica composite sorbents for clean-up and preconcentration. Sample clean-up for alkaloids (hydrastine and berberine) in goldenseal, Hydrastis canadensis and flavonoids (quercetin, kaempferol and isorhamnetin) in Ginkgo biloba was achieved using Bond Elut Plexa SPE sorbent. Clean-up of flavonoids in Ginkgo biloba was also achieved using electrospun polymer-silica composite (polystyrene-silica, polyacrylonitrile-silica and nylon 6-silica) sorbents. All analysis of flavonoids and alkaloids was carried out using an Agilent 1200 Series HPLC coupled with a diode array detector. Good peak separation was achieved in less than 6 min employing an Agilent ZORBAX Eclipse Plus C18 column (4.6 x 75 mm, 3.5 μm) at 35⁰C. The mobile phases employed were 0.1% phosphoric acid/methanol gradient and 0.5% phosphoric acid/methanol (40:60) for alkaloids and flavonoids respectively. The calibration curves exhibited linearity up to 120 μg mL⁻¹ with correlation coefficients of more than 0.9980. The recoveries ranged from 73-109% with relative standard deviation of less than 5% for all analytes. Agilent Chem Elut supported liquid extraction was employed for the development of a sample preparation method for the determination of 24 banned aromatic amines from azo dyes in textile following the EU standard method EN 14362-1:2003 (E) and the Chinese standard method GB/T 17592-2006. The supported liquid extraction was effective in the extraction of the aromatic amines from textile (cotton, wool and polyester/cotton [80%:20%]). Most of the recoveries obtained were conforming to the minimum requirements set in the EN 14362-1:2003 (E) standard method and the relative standard deviations were less than 15%. Good peak separation was obtained within 70 min run time using the Agilent Zorbax SB-Phenyl column (4.6 mm x 250 mm, 5-micron) or the Agilent DB-35 MS (J & W) (30 m x 0.25 mm, 0.25 μm film thickness. It was demonstrated that the polymeric Agilent Bond Elut Plexa, electrospun nanofibers and diatomaceous earth were effective in extraction of alkaloids, flavonoids and aromatic amines in different matrices. The developed methods were simple, rapid and reproducible.
- Full Text:
Polymer based electrospun nanofibers as diagnostic probes for the detection of toxic metal ions in water
- Authors: Ondigo, Dezzline Adhiambo
- Date: 2013
- Subjects: Heavy metals , Nanofibers , Nanoparticles , Colorimetric analysis
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4557 , http://hdl.handle.net/10962/d1018261
- Description: The thesis presents the development of polymer based electrospun nanofibers as diagnostic probes for the selective detection of toxic metal ions in water. Through modification of the chemical characteristics of nanofibers by pre- and post-electrospinning treatments, three different diagnostic probes were successfully developed. These were the fluorescent pyridylazo-2-naphthol-poly(acrylic acid) nanofiber probe, the colorimetric probe based on glutathione-stabilized silver/copper alloy nanoparticles and the colorimetric probe based on 2-(2’-Pyridyl)-imidazole functionalized nanofibers. The probes were characterized by Fourier transform infrared spectroscopy (FTIR), Energy dispersive x-ray spectroscopy (EDX), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The fluorescent nanofiber probe was developed towards the determination of Ni²⁺. Covalently functionalized pyridylazo-2-naphthol-poly(acrylic acid) polymeric nanofibers were employed. The solid state Ni²⁺ probe exhibited a good correlation between the fluorescence intensity and nickel concentration up to 1.0 mg/mL based on the Stern-Volmer mechanism. The detection limit of the nanofiber probe was found to be 0.07 ng/mL. The versatility of the fluorescent probe was demonstrated by affording a simple, rapid and selective detection of Ni²⁺ in the presence of other competing metal ions by direct analysis without employing any sample handling steps. For the second part of the study, a simple strategy based on the in-situ synthesis of the glutathione stabilized silver/copper alloy nanoparticles (Ag/Cu alloy NPs) in nylon 6 provided a fast procedure for fabricating a colorimetric probe for the detection of Ni²⁺ in water samples. The electrospun nanofiber composites responded to Ni²⁺ ions but did not suffer any interference from the other metal ions. The effect of Ni²⁺ concentration on the nanocomposite fibers was considered and the “eye-ball” limit of detection was found to be 5.8 μg/mL. Lastly, the third probe was developed by covalently linking an imidazole derivative; 2-(2′-Pyridyl)-imidazole (PIMH) to Poly(vinylbenzyl chloride) (PVBC) and nylon 6 nanofibers by post-electrospinning treatments using a wet chemical method and graft copolymerization technique, respectively. The post-electrospinning modifications of the nanofibers were achieved without altering their fibrous morphology. The color change to red-orange in the presence of Fe²⁺ for both the grafted nylon 6 (white) and the chemically modified PVBC (yellow) nanofibers was instantaneous. The developed diagnostic probes exhibited the desired selectivity towards the targeted metal ions.
- Full Text:
- Authors: Ondigo, Dezzline Adhiambo
- Date: 2013
- Subjects: Heavy metals , Nanofibers , Nanoparticles , Colorimetric analysis
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4557 , http://hdl.handle.net/10962/d1018261
- Description: The thesis presents the development of polymer based electrospun nanofibers as diagnostic probes for the selective detection of toxic metal ions in water. Through modification of the chemical characteristics of nanofibers by pre- and post-electrospinning treatments, three different diagnostic probes were successfully developed. These were the fluorescent pyridylazo-2-naphthol-poly(acrylic acid) nanofiber probe, the colorimetric probe based on glutathione-stabilized silver/copper alloy nanoparticles and the colorimetric probe based on 2-(2’-Pyridyl)-imidazole functionalized nanofibers. The probes were characterized by Fourier transform infrared spectroscopy (FTIR), Energy dispersive x-ray spectroscopy (EDX), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The fluorescent nanofiber probe was developed towards the determination of Ni²⁺. Covalently functionalized pyridylazo-2-naphthol-poly(acrylic acid) polymeric nanofibers were employed. The solid state Ni²⁺ probe exhibited a good correlation between the fluorescence intensity and nickel concentration up to 1.0 mg/mL based on the Stern-Volmer mechanism. The detection limit of the nanofiber probe was found to be 0.07 ng/mL. The versatility of the fluorescent probe was demonstrated by affording a simple, rapid and selective detection of Ni²⁺ in the presence of other competing metal ions by direct analysis without employing any sample handling steps. For the second part of the study, a simple strategy based on the in-situ synthesis of the glutathione stabilized silver/copper alloy nanoparticles (Ag/Cu alloy NPs) in nylon 6 provided a fast procedure for fabricating a colorimetric probe for the detection of Ni²⁺ in water samples. The electrospun nanofiber composites responded to Ni²⁺ ions but did not suffer any interference from the other metal ions. The effect of Ni²⁺ concentration on the nanocomposite fibers was considered and the “eye-ball” limit of detection was found to be 5.8 μg/mL. Lastly, the third probe was developed by covalently linking an imidazole derivative; 2-(2′-Pyridyl)-imidazole (PIMH) to Poly(vinylbenzyl chloride) (PVBC) and nylon 6 nanofibers by post-electrospinning treatments using a wet chemical method and graft copolymerization technique, respectively. The post-electrospinning modifications of the nanofibers were achieved without altering their fibrous morphology. The color change to red-orange in the presence of Fe²⁺ for both the grafted nylon 6 (white) and the chemically modified PVBC (yellow) nanofibers was instantaneous. The developed diagnostic probes exhibited the desired selectivity towards the targeted metal ions.
- Full Text:
- «
- ‹
- 1
- ›
- »