Dynamics of stimulated luminescence in natural quartz: Thermoluminescence and phototransferred thermoluminescence
- Authors: Folley, Damilola Esther
- Date: 2020
- Subjects: Thermoluminescence , Quartz
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/146255 , vital:38509
- Description: Natural quartz has remained an important mineral that is of topical interest in luminescence and dosimetry-related research. We investigate the dynamics of stimulated luminescence on this material through thermoluminescence (TL) and phototransferred thermoluminescence (PTTL). Measurements were made on unannealed natural quartz as well as quartz annealed at 800 and 1000̊C. The samples were annealed for 10 minutes and for 1 hour. The material, in its un- and annealed state has its main peak between 68 and 72̊C when measured at 1Cs ̃1 after a dose of 50 Gy. A study of dosimetric features and kinetic analysis was carried out on two prominent peaks, peak I and III for all the samples. The peaks show a sublinear dose response for irradiation doses between 10 and 300 Gy. Kinetic analysis shows that peak I is a first-order peak and peak III a general-order peak. Interestingly, we observe for peak I for the sample annealed at 800̊C for 1 hour an inverse thermal quenching behaviour. We demonstrate that a peak affected with an inverse thermal quenching-like behaviour can still show effect of thermal quenching when the dose the sample is irradiated to is significantly reduced. We ascribe the apparent dependence of thermal quenching on dose to competition between radiative and non-radiative transitions at the recombination centre. Peaks I, II, and III for all the samples were reproduced under phototransfer when the peaks, initially removed by preheating to a certain temperature are exposed to 470 and 525 nm light. The infuence of duration of illumination on the PTTL intensity of these peaks corresponding to various preheating temperatures is modelled using coupled first-order dfferential equations. The model is based on systems of acceptors and donors whose number and role depends on preheating temperature
- Full Text:
- Date Issued: 2020
- Authors: Folley, Damilola Esther
- Date: 2020
- Subjects: Thermoluminescence , Quartz
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/146255 , vital:38509
- Description: Natural quartz has remained an important mineral that is of topical interest in luminescence and dosimetry-related research. We investigate the dynamics of stimulated luminescence on this material through thermoluminescence (TL) and phototransferred thermoluminescence (PTTL). Measurements were made on unannealed natural quartz as well as quartz annealed at 800 and 1000̊C. The samples were annealed for 10 minutes and for 1 hour. The material, in its un- and annealed state has its main peak between 68 and 72̊C when measured at 1Cs ̃1 after a dose of 50 Gy. A study of dosimetric features and kinetic analysis was carried out on two prominent peaks, peak I and III for all the samples. The peaks show a sublinear dose response for irradiation doses between 10 and 300 Gy. Kinetic analysis shows that peak I is a first-order peak and peak III a general-order peak. Interestingly, we observe for peak I for the sample annealed at 800̊C for 1 hour an inverse thermal quenching behaviour. We demonstrate that a peak affected with an inverse thermal quenching-like behaviour can still show effect of thermal quenching when the dose the sample is irradiated to is significantly reduced. We ascribe the apparent dependence of thermal quenching on dose to competition between radiative and non-radiative transitions at the recombination centre. Peaks I, II, and III for all the samples were reproduced under phototransfer when the peaks, initially removed by preheating to a certain temperature are exposed to 470 and 525 nm light. The infuence of duration of illumination on the PTTL intensity of these peaks corresponding to various preheating temperatures is modelled using coupled first-order dfferential equations. The model is based on systems of acceptors and donors whose number and role depends on preheating temperature
- Full Text:
- Date Issued: 2020
Thermoluminescence and phototransferred phermoluminescence of synthetic quartz
- Authors: Dawam, Robert Rangmou
- Date: 2020
- Subjects: Thermoluminescence , Quartz
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/145849 , vital:38472
- Description: The main aim of this investigation is on thermoluminescence and phototransferred thermoluminescence of synthetic quartz. Thermoluminescence was one of the tools used in characterising the electron traps parameters. The samples of quartz annealed at various temperatures up to 900̊C and the unannealed were used. The thermoluminescence glow curve was measured at 1̊C s~ 1 following beta irradiation to 40 Gy from the samples annealed at 500̊C and the unannealed consist of main peak at 70̊C and secondary peaks at 110, 180 and 310̊C. In comparison, the thermoluminescence glow curve for the sample annealed at 900̊C have main peak at 86̊C and the secondary ones at 170 and 310̊C. The kinetic analysis was carried out only on the main peak in each case. The activation energy was found to be decreasing with increase in annealing temperatures. The samples annealed at 500̊C and the unannealed were found to be affected by thermal quenching while sample annealed at 900̊C shows an inverse quenching for irradiation dose of 40 Gy. However, when the dose was reduce to 3 Gy the effects of thermal quenching was manifested. The activation energy of thermal quenching was also found to decrease with increase in annealing temperature. Thermally assisted optically stimulated luminescence measurement was carried out using continuous wave optical stimulated luminescence (CW-OSL). The samples studied were those annealed at 500̊C for 10 minutes, 900̊C for 10, 30, 60 minutes and 1000̊C for 10 minutes prior to use. The CW-OSL is stimulated using 470 nm blue LEDs at sample temperatures between 30 and 200̊C. It is measured after preheating to either 300 and 500̊C. When the integrated OSL intensity is plotted as a function of measurement temperature, the intensity goes through a peak. The increase in OSL intensity as a function of temperature is associated to thermal assistance and the decrease to thermal quenching. The kinetic parameters were evaluated by fitting the experimental data. The values of activation energies of thermal quenching are the same within experimental uncertainties for all the experimental conditions. This shows that annealing temperature, duration of annealing and irradiation dose have a negligible influence on the recombination site of luminescence using OSL. Phototransferred thermoluminescence (PTTL) induced from annealed samples using 470 nm blue light was also investigated. The quartz were annealed at 500 _C for 10 minutes, 900̊C for 10, 30, 60 minutes and 1000̊C for 10 minutes prior to use. The glow curves of conventional TL measured at 1 _C s1 following irradiation to 200 Gy shows six peaks in each case labelled I-VI for ease of reference whereas peaks observed under PTTL are referred to as A1 onwards. Only the first three peaks were reproduced under phototransfer for the sample annealed at 900̊C for 60 minutes and 1000̊C C for 10 minutes. Interestingly, for the intermediate duration of annealing of 30 minutes, the only peak that appears under phototransfer is the A1. For quartz annealed at 900̊C for 10 minutes, the PTTL appears as long as the preheating temperature does not exceed 560̊C. All other annealing temperatures, PTTL only appears for preheating to 450 and below. This shows that the occupancy of deep electron traps at temperatures beyond 450̊C or 560̊C is low. The activation energy for peaks A1, A2 and A3 were calculated. The PTTL peaks were studied for thermal quenching and peaks A1 and A3 were found to be affected. The activation energies for thermal quenching were determined as 0.62 ± 0.04 eV and 0.65 ± 0.02 eV for peaks A1 and A3 respectively. The experimental dependence of PTTL intensity on illumination time is modelled using sets of coupled linear differential equations based on systems of donors and acceptors whose number is determined by preheating temperature.
- Full Text:
- Date Issued: 2020
- Authors: Dawam, Robert Rangmou
- Date: 2020
- Subjects: Thermoluminescence , Quartz
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/145849 , vital:38472
- Description: The main aim of this investigation is on thermoluminescence and phototransferred thermoluminescence of synthetic quartz. Thermoluminescence was one of the tools used in characterising the electron traps parameters. The samples of quartz annealed at various temperatures up to 900̊C and the unannealed were used. The thermoluminescence glow curve was measured at 1̊C s~ 1 following beta irradiation to 40 Gy from the samples annealed at 500̊C and the unannealed consist of main peak at 70̊C and secondary peaks at 110, 180 and 310̊C. In comparison, the thermoluminescence glow curve for the sample annealed at 900̊C have main peak at 86̊C and the secondary ones at 170 and 310̊C. The kinetic analysis was carried out only on the main peak in each case. The activation energy was found to be decreasing with increase in annealing temperatures. The samples annealed at 500̊C and the unannealed were found to be affected by thermal quenching while sample annealed at 900̊C shows an inverse quenching for irradiation dose of 40 Gy. However, when the dose was reduce to 3 Gy the effects of thermal quenching was manifested. The activation energy of thermal quenching was also found to decrease with increase in annealing temperature. Thermally assisted optically stimulated luminescence measurement was carried out using continuous wave optical stimulated luminescence (CW-OSL). The samples studied were those annealed at 500̊C for 10 minutes, 900̊C for 10, 30, 60 minutes and 1000̊C for 10 minutes prior to use. The CW-OSL is stimulated using 470 nm blue LEDs at sample temperatures between 30 and 200̊C. It is measured after preheating to either 300 and 500̊C. When the integrated OSL intensity is plotted as a function of measurement temperature, the intensity goes through a peak. The increase in OSL intensity as a function of temperature is associated to thermal assistance and the decrease to thermal quenching. The kinetic parameters were evaluated by fitting the experimental data. The values of activation energies of thermal quenching are the same within experimental uncertainties for all the experimental conditions. This shows that annealing temperature, duration of annealing and irradiation dose have a negligible influence on the recombination site of luminescence using OSL. Phototransferred thermoluminescence (PTTL) induced from annealed samples using 470 nm blue light was also investigated. The quartz were annealed at 500 _C for 10 minutes, 900̊C for 10, 30, 60 minutes and 1000̊C for 10 minutes prior to use. The glow curves of conventional TL measured at 1 _C s1 following irradiation to 200 Gy shows six peaks in each case labelled I-VI for ease of reference whereas peaks observed under PTTL are referred to as A1 onwards. Only the first three peaks were reproduced under phototransfer for the sample annealed at 900̊C for 60 minutes and 1000̊C C for 10 minutes. Interestingly, for the intermediate duration of annealing of 30 minutes, the only peak that appears under phototransfer is the A1. For quartz annealed at 900̊C for 10 minutes, the PTTL appears as long as the preheating temperature does not exceed 560̊C. All other annealing temperatures, PTTL only appears for preheating to 450 and below. This shows that the occupancy of deep electron traps at temperatures beyond 450̊C or 560̊C is low. The activation energy for peaks A1, A2 and A3 were calculated. The PTTL peaks were studied for thermal quenching and peaks A1 and A3 were found to be affected. The activation energies for thermal quenching were determined as 0.62 ± 0.04 eV and 0.65 ± 0.02 eV for peaks A1 and A3 respectively. The experimental dependence of PTTL intensity on illumination time is modelled using sets of coupled linear differential equations based on systems of donors and acceptors whose number is determined by preheating temperature.
- Full Text:
- Date Issued: 2020
Thermoluminescence characteristics of synthetic quartz
- Authors: Niyonzima, Pontien
- Date: 2014
- Subjects: Thermoluminescence , Quartz , Emission spectroscopy
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:5538 , http://hdl.handle.net/10962/d1013190
- Description: Quartz is one of the most abundant natural minerals in the crust of the earth. Due to its dosimetric luminescence properties, it is employed in retrospective dosimetry, archaeological and geological dating. The intensity and the structure of the TL glow curves of quartz are strongly dependent upon the origin, impurity content, formation condition and pre-irradiation heat treatment. The aim of this project is to study the mechanisms of thermoluminescence (TL), Phototranssferred thermoluminescence (PTTL) and radioluminescence (RL) in synthetic quartz and to discuss the results in terms of physical characteristics of point defects involved. Thermoluminescence measurements were made on a sample of synthetic quartz in its as-received state (unannealed) synthetic quartz annealed at 500˚C for 10 minutes. The unannealed sample shows six TL glow peaks located at 94, 116, 176, 212, 280 and 348˚C at a heating rate of 5˚Cs⁻¹. The annealed sample shows seven TL peaks at 115, 148, 214, 246, 300, 348 and 412˚C at a heating rate of 5˚Cs⁻¹. The intensity of peak I, at 94 and 115˚C for the unannealed and annealed samples respectively, increases with irradiation. Peak I has an activation energy of approximately 0.90 eV and a frequency factor of the order of 10¹¹ s⁻¹. The order of kinetics is between 0.9 and 1.2. The unannealed synthetic quartz shows phototransferred thermoluminescence (PTTL) at the position of peak I after removal of the first three peaks followed by illumination. The PTTL intensities show peak shaped behaviour when plotted against illumination time. The PTTL showed a quadratic increase with dose. The material exhibits fading of PTTL intensity with delay time. Radioluminescence was measured on synthetic quartz unannealed and annealed annealed at 500, 600, 700, 800, 900 and 1000˚C for 10 to 60 min. The emission spectra of synthetic quartz show seven emission bands. The effect of irradiation on the RL spectra is to increase the intensity of all emission bands for samples annealed at temperatures less than or equal to 700˚C. The effect of annealing time is to increase the RL amplitude for the samples annealed at temperatures greater than 700˚C. The annealing temperature increases the RL amplitude of all emission bands of the spectrum for all samples.
- Full Text:
- Date Issued: 2014
- Authors: Niyonzima, Pontien
- Date: 2014
- Subjects: Thermoluminescence , Quartz , Emission spectroscopy
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:5538 , http://hdl.handle.net/10962/d1013190
- Description: Quartz is one of the most abundant natural minerals in the crust of the earth. Due to its dosimetric luminescence properties, it is employed in retrospective dosimetry, archaeological and geological dating. The intensity and the structure of the TL glow curves of quartz are strongly dependent upon the origin, impurity content, formation condition and pre-irradiation heat treatment. The aim of this project is to study the mechanisms of thermoluminescence (TL), Phototranssferred thermoluminescence (PTTL) and radioluminescence (RL) in synthetic quartz and to discuss the results in terms of physical characteristics of point defects involved. Thermoluminescence measurements were made on a sample of synthetic quartz in its as-received state (unannealed) synthetic quartz annealed at 500˚C for 10 minutes. The unannealed sample shows six TL glow peaks located at 94, 116, 176, 212, 280 and 348˚C at a heating rate of 5˚Cs⁻¹. The annealed sample shows seven TL peaks at 115, 148, 214, 246, 300, 348 and 412˚C at a heating rate of 5˚Cs⁻¹. The intensity of peak I, at 94 and 115˚C for the unannealed and annealed samples respectively, increases with irradiation. Peak I has an activation energy of approximately 0.90 eV and a frequency factor of the order of 10¹¹ s⁻¹. The order of kinetics is between 0.9 and 1.2. The unannealed synthetic quartz shows phototransferred thermoluminescence (PTTL) at the position of peak I after removal of the first three peaks followed by illumination. The PTTL intensities show peak shaped behaviour when plotted against illumination time. The PTTL showed a quadratic increase with dose. The material exhibits fading of PTTL intensity with delay time. Radioluminescence was measured on synthetic quartz unannealed and annealed annealed at 500, 600, 700, 800, 900 and 1000˚C for 10 to 60 min. The emission spectra of synthetic quartz show seven emission bands. The effect of irradiation on the RL spectra is to increase the intensity of all emission bands for samples annealed at temperatures less than or equal to 700˚C. The effect of annealing time is to increase the RL amplitude for the samples annealed at temperatures greater than 700˚C. The annealing temperature increases the RL amplitude of all emission bands of the spectrum for all samples.
- Full Text:
- Date Issued: 2014
Thermoluminescence of natural quartz
- Authors: Lontsi Sob, Aaron Joel
- Date: 2014
- Subjects: Thermoluminescence , Quartz , Thermoluminescence dosimetry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:5543 , http://hdl.handle.net/10962/d1013358
- Description: The kinetic and dosimetric features of the main thermoluminescence peak of quartz have been investigated in unannealed as well in quartz annealed at 500˚C for 10 minutes. The main peak is found at 92 and 86˚C respectively for aliquots of unannealed and annealed samples irradiated to 10 Gy and heated at 5.0˚C/s. For each sample, the intensity of the main peak is enhanced with repetitive measurement whereas its maximum temperature is unaffected. The peak position of the main peak in each sample is independent of the irradiation dose and this, together with its fading characteristics are consistent with first-order kinetics. For low doses, typically between 2 and 10 Gy, the dose response of the main peak in each sample is linear. In the intermediate dose range from 10 to 60 Gy, the growth of the main peak in each sample is sub-linear and for greater doses, in the range from 60 Gy to 151 Gy, it is linear again. The half-life of the main peak of the unannealed sample is about 1.3 h whereas that of the annealed sample is about 1.2 h. The main peak in each sample can be approximated to a first-order glow peak. As the heating rate increases, the intensity of the main peak in each sample decreases. This is evidence of thermal quenching. The main peak in each sample is the only peak regenerated by phototransfer. The resulting phototransferred peak occurs at the same temperature as the original peak and has similar kinetic and dosimetric features. For a preheat temperature of 120˚C, the intensity of the phototransferred peak in each sample increases with illumination time up to a maximum and decreases afterwards. At longer illumination times (such as 30 min up to 1 h), no further decrease in the intensity of the phototransferred peak is observed. The traps associated with the 325˚C peak are the main source of the electrons responsible for the regenerated peak. Radioluminescence emission spectra were also measured for quartz annealed at various temperatures. Emission bands in quartz are affected by annealing and irradiation. A strong enhancement of the 3.4 eV (~366 nm) emission band is observed in quartz annealed at 500˚C. A new emission band which grows with annealing up to 1000˚C is observed at 3.7 eV (~330 nm) for quartz annealed at 600˚C. An attempt has been made to correlate the changes in radioluminescence emission spectra due to annealing with the influence of annealing on luminescence lifetimes in quartz.
- Full Text:
- Date Issued: 2014
- Authors: Lontsi Sob, Aaron Joel
- Date: 2014
- Subjects: Thermoluminescence , Quartz , Thermoluminescence dosimetry
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:5543 , http://hdl.handle.net/10962/d1013358
- Description: The kinetic and dosimetric features of the main thermoluminescence peak of quartz have been investigated in unannealed as well in quartz annealed at 500˚C for 10 minutes. The main peak is found at 92 and 86˚C respectively for aliquots of unannealed and annealed samples irradiated to 10 Gy and heated at 5.0˚C/s. For each sample, the intensity of the main peak is enhanced with repetitive measurement whereas its maximum temperature is unaffected. The peak position of the main peak in each sample is independent of the irradiation dose and this, together with its fading characteristics are consistent with first-order kinetics. For low doses, typically between 2 and 10 Gy, the dose response of the main peak in each sample is linear. In the intermediate dose range from 10 to 60 Gy, the growth of the main peak in each sample is sub-linear and for greater doses, in the range from 60 Gy to 151 Gy, it is linear again. The half-life of the main peak of the unannealed sample is about 1.3 h whereas that of the annealed sample is about 1.2 h. The main peak in each sample can be approximated to a first-order glow peak. As the heating rate increases, the intensity of the main peak in each sample decreases. This is evidence of thermal quenching. The main peak in each sample is the only peak regenerated by phototransfer. The resulting phototransferred peak occurs at the same temperature as the original peak and has similar kinetic and dosimetric features. For a preheat temperature of 120˚C, the intensity of the phototransferred peak in each sample increases with illumination time up to a maximum and decreases afterwards. At longer illumination times (such as 30 min up to 1 h), no further decrease in the intensity of the phototransferred peak is observed. The traps associated with the 325˚C peak are the main source of the electrons responsible for the regenerated peak. Radioluminescence emission spectra were also measured for quartz annealed at various temperatures. Emission bands in quartz are affected by annealing and irradiation. A strong enhancement of the 3.4 eV (~366 nm) emission band is observed in quartz annealed at 500˚C. A new emission band which grows with annealing up to 1000˚C is observed at 3.7 eV (~330 nm) for quartz annealed at 600˚C. An attempt has been made to correlate the changes in radioluminescence emission spectra due to annealing with the influence of annealing on luminescence lifetimes in quartz.
- Full Text:
- Date Issued: 2014
- «
- ‹
- 1
- ›
- »