Electrical power output estimation model for a conical diffuser augmented wind turbine
- Authors: Masukume, Peace-Maker
- Date: 2016
- Subjects: Wind power , Wind turbines , Renewable energy sources
- Language: English
- Type: Thesis , Doctoral , DPhil
- Identifier: http://hdl.handle.net/10353/1517 , vital:27404
- Description: Energy is integral to the quality of life of any society. However, meeting the demand for energy sustainably is the main challenge facing humanity. In general, non-renewable energy resources are used to supply the ever increasing energy demand. However, the extraction and processing of these resources is accompanied by the production of wastes which are a health hazard and impact negatively on climate change. Considering the finite nature of non-renewable sources, the environmental concerns which are associated with their usage and ensuring energy security, renewable energy sources have been brought in the energy supply chain. Wind energy is one of the renewable energy sources which has been supplying electrical energy to the ever increasing energy demand of humanity. Wind energy technology is a mature technology which over and above the bare (conventional) wind turbine technology has seen the development of duct augmented wind turbines. Ducts are used to encase wind turbine rotors to augment the power output of wind turbines especially in low wind speed areas. Though the technology has been under study for decades now, research indicates that there is no known model to estimate the power output of a diffuser augmented wind turbine. This thesis presents the development of the conical Diffuser Augmented Wind Turbine (DAWT) power output estimation model and its validation.
- Full Text:
- Date Issued: 2016
- Authors: Masukume, Peace-Maker
- Date: 2016
- Subjects: Wind power , Wind turbines , Renewable energy sources
- Language: English
- Type: Thesis , Doctoral , DPhil
- Identifier: http://hdl.handle.net/10353/1517 , vital:27404
- Description: Energy is integral to the quality of life of any society. However, meeting the demand for energy sustainably is the main challenge facing humanity. In general, non-renewable energy resources are used to supply the ever increasing energy demand. However, the extraction and processing of these resources is accompanied by the production of wastes which are a health hazard and impact negatively on climate change. Considering the finite nature of non-renewable sources, the environmental concerns which are associated with their usage and ensuring energy security, renewable energy sources have been brought in the energy supply chain. Wind energy is one of the renewable energy sources which has been supplying electrical energy to the ever increasing energy demand of humanity. Wind energy technology is a mature technology which over and above the bare (conventional) wind turbine technology has seen the development of duct augmented wind turbines. Ducts are used to encase wind turbine rotors to augment the power output of wind turbines especially in low wind speed areas. Though the technology has been under study for decades now, research indicates that there is no known model to estimate the power output of a diffuser augmented wind turbine. This thesis presents the development of the conical Diffuser Augmented Wind Turbine (DAWT) power output estimation model and its validation.
- Full Text:
- Date Issued: 2016
Statistical tools for wind energy generation
- Authors: Ndzukuma, Sibusiso
- Date: 2012
- Subjects: Wind power , Wind turbines , Winds -- Speed
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:10580 , http://hdl.handle.net/10948/d1020627
- Description: In this study we conduct wind resource assessment to evaluate the annual energy production of a wind turbine. To estimate energy production of a wind turbine over a period of time, the power characteristics of the wind turbine are integrated with the probabilities of the wind speed expected at a chosen site. The first data set was obtained from a wind farm in Denmark. We propose several probability density functions to model the distribution of the wind speed. We use techniques from nonlinear regression analysis to model the power curve of a wind turbine. The best fit distribution model is assessed by performing numeric goodness–of–fit measures and graphical analyses. Johnson’s bounded (SB) distribution provides the best fit model with the smallest Kolmogorov–Smirnov (K-S) test statistic . 15. The four parameter logistic nonlinear regression (4PL) model is determined to provide the best fit to the power curve data, according to the Akaike Information Criterion (AIC) and the Bayesian Information Criterion (BIC). The estimated annual energy yield is compared to the actual production of the wind turbine. Our models underestimate the actual energy production by a 1 difference. In Chapter Six we conduct data processing, analyses and comparison of wind speed distributions using a data set obtained from a measuring wind mast mounted in Humansdorp, Eastern Cape. The expected annual energy production is estimated by using the certified power curve as provided by the manufacturer of the wind turbine under study. The commonly used Weibull distribution is determined to provide the best fit distribution model to our selected models. The annual energy yield is estimated at 7.33 GWh, with a capacity factor of 41.8 percent.
- Full Text:
- Date Issued: 2012
- Authors: Ndzukuma, Sibusiso
- Date: 2012
- Subjects: Wind power , Wind turbines , Winds -- Speed
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:10580 , http://hdl.handle.net/10948/d1020627
- Description: In this study we conduct wind resource assessment to evaluate the annual energy production of a wind turbine. To estimate energy production of a wind turbine over a period of time, the power characteristics of the wind turbine are integrated with the probabilities of the wind speed expected at a chosen site. The first data set was obtained from a wind farm in Denmark. We propose several probability density functions to model the distribution of the wind speed. We use techniques from nonlinear regression analysis to model the power curve of a wind turbine. The best fit distribution model is assessed by performing numeric goodness–of–fit measures and graphical analyses. Johnson’s bounded (SB) distribution provides the best fit model with the smallest Kolmogorov–Smirnov (K-S) test statistic . 15. The four parameter logistic nonlinear regression (4PL) model is determined to provide the best fit to the power curve data, according to the Akaike Information Criterion (AIC) and the Bayesian Information Criterion (BIC). The estimated annual energy yield is compared to the actual production of the wind turbine. Our models underestimate the actual energy production by a 1 difference. In Chapter Six we conduct data processing, analyses and comparison of wind speed distributions using a data set obtained from a measuring wind mast mounted in Humansdorp, Eastern Cape. The expected annual energy production is estimated by using the certified power curve as provided by the manufacturer of the wind turbine under study. The commonly used Weibull distribution is determined to provide the best fit distribution model to our selected models. The annual energy yield is estimated at 7.33 GWh, with a capacity factor of 41.8 percent.
- Full Text:
- Date Issued: 2012
An economic evaluation of a wind power electricity generating farm in South Africa
- Authors: Menzies, Greig Hamilton
- Date: 2011
- Subjects: Wind power -- Economic aspects -- South Africa , Wind power plants -- Environmental aspects -- South Africa , Wind turbines
- Language: English
- Type: Thesis , Masters , MCom
- Identifier: vital:8987 , http://hdl.handle.net/10948/1335 , Wind power -- Economic aspects -- South Africa , Wind power plants -- Environmental aspects -- South Africa , Wind turbines
- Description: Renewable energy technology has received much attention over recent years. The depletion of known fossil fuel reserves and the volatility of international fuel prices require that society looks beyond the current coal-dominated electricity generation methods. Wind energy is an internationally well-established technology with large markets in major countries around the world, such as the USA and Germany. South Africa has the potential to generate large amounts of electricity from the wind because of the strength of the country’s wind resource. The long coast line and open areas are ideal for the exploitation of wind energy. A wind farm project has been proposed for development near the town of Jeffrey’s Bay, in the Eastern Cape. The proposed project involves the construction and installation of a 15MW wind farm, consisting of 6-10 turbines standing 120m tall, over an area of 20ha.There are indirect costs and benefits (externalities) associated with a wind farm project and it is important that projects such as these are evaluated from a social standpoint. The aim of this study was to determine the compensation required by residents for siting a wind farm in their area. This compensation was then used as a component of an overall evaluation of the project.
- Full Text:
- Date Issued: 2011
- Authors: Menzies, Greig Hamilton
- Date: 2011
- Subjects: Wind power -- Economic aspects -- South Africa , Wind power plants -- Environmental aspects -- South Africa , Wind turbines
- Language: English
- Type: Thesis , Masters , MCom
- Identifier: vital:8987 , http://hdl.handle.net/10948/1335 , Wind power -- Economic aspects -- South Africa , Wind power plants -- Environmental aspects -- South Africa , Wind turbines
- Description: Renewable energy technology has received much attention over recent years. The depletion of known fossil fuel reserves and the volatility of international fuel prices require that society looks beyond the current coal-dominated electricity generation methods. Wind energy is an internationally well-established technology with large markets in major countries around the world, such as the USA and Germany. South Africa has the potential to generate large amounts of electricity from the wind because of the strength of the country’s wind resource. The long coast line and open areas are ideal for the exploitation of wind energy. A wind farm project has been proposed for development near the town of Jeffrey’s Bay, in the Eastern Cape. The proposed project involves the construction and installation of a 15MW wind farm, consisting of 6-10 turbines standing 120m tall, over an area of 20ha.There are indirect costs and benefits (externalities) associated with a wind farm project and it is important that projects such as these are evaluated from a social standpoint. The aim of this study was to determine the compensation required by residents for siting a wind farm in their area. This compensation was then used as a component of an overall evaluation of the project.
- Full Text:
- Date Issued: 2011
Development of a reciprocating aerofoil wind energy harvester
- Authors: Phillips, Russell Leslie
- Date: 2008
- Subjects: Windmills , Wind power , Wind turbines
- Language: English
- Type: Thesis , Doctoral , DTech
- Identifier: vital:9622 , http://hdl.handle.net/10948/899 , Windmills , Wind power , Wind turbines
- Description: Cross flow wind turbines are not unique. The performance of Savonius and Darrieus turbines is well documented. Both share the advantage of being able to accept fluid flow from any direction. The Savonius is drag based and hence has poor power output while the Darrieus is lift based. Due to the fact that the Darrieus has fixed blades the fluid flow through the rotor does not result in optimal lift being generated at all points in the rotation circle. A drawback of the Darrieus system is that it has to operate at a high tip-to wind-speed ratio to obtain reasonable performance with the fixed blades. Deviation from a small optimal range of tip speed ratios results in poor performance. The Darrieus also has poor starting torque. The research conducted in this project focused on overcoming the shortcomings of other turbines and developing an effective cross flow turbine capable of good performance. A number of different concepts were experimented with, however all were based on a symmetrical aerofoil presented to the actual relative airflow at an angle that would produce the highest lift force at all times. The lift force was then utilized to generate movement and to do work on an electrical generator. All concepts contemplated were researched to ascertain their appropriateness for the intended application. During development of the final experimental platform and after lodging of a provisional patent (RSA 2007/00927) it was ascertained that the design shared some similarities with an American patent 5503525 dated 28/4/1994. This patent employed complex electronic sensing and control equipment for control of blade angle. This was thought to be overly complex and costly, particularly for small scale wind energy generation applications and a simpler mechanical solution was sought in the design of the final experimental platform used in this project. The design of the mechanical control system was refined in an attempt to make it simpler, more durable and employ the least number of moving parts. Literature studies and patent searches conducted, suggested that the mechanical control system as developed for the final experimental platform was unique. The enormous variation in the power available from the wind at the different wind speeds likely to be encountered by the device necessitated some means of control. In high wind conditions control of the amount of wind power into the device was deemed to be the preferable means of control. A number of different concepts to achieve this were devised and tested. The final concept employed limited the tail angle deflection and hence the lift produced by the aerofoils. This resulted in a seamless “throttle” control allowing the device to be used in any wind strength by adjusting the control to a position that resulted in the device receiving a suitable amount of power from the wind. The outcome of performance tests conducted indicated that the device has the potential to be developed into a viable wind turbine for both small and large scale applications. The ability to control the power input from the wind to the machine from zero to a maximum is considered to be one of the most beneficial outcomes of this project and together with the quiet operation and low speed, are considered the main advantages of the device over existing wind turbine designs. The possibilities of using the device to compress air for energy storage are exciting avenues that warrant further research.
- Full Text:
- Date Issued: 2008
- Authors: Phillips, Russell Leslie
- Date: 2008
- Subjects: Windmills , Wind power , Wind turbines
- Language: English
- Type: Thesis , Doctoral , DTech
- Identifier: vital:9622 , http://hdl.handle.net/10948/899 , Windmills , Wind power , Wind turbines
- Description: Cross flow wind turbines are not unique. The performance of Savonius and Darrieus turbines is well documented. Both share the advantage of being able to accept fluid flow from any direction. The Savonius is drag based and hence has poor power output while the Darrieus is lift based. Due to the fact that the Darrieus has fixed blades the fluid flow through the rotor does not result in optimal lift being generated at all points in the rotation circle. A drawback of the Darrieus system is that it has to operate at a high tip-to wind-speed ratio to obtain reasonable performance with the fixed blades. Deviation from a small optimal range of tip speed ratios results in poor performance. The Darrieus also has poor starting torque. The research conducted in this project focused on overcoming the shortcomings of other turbines and developing an effective cross flow turbine capable of good performance. A number of different concepts were experimented with, however all were based on a symmetrical aerofoil presented to the actual relative airflow at an angle that would produce the highest lift force at all times. The lift force was then utilized to generate movement and to do work on an electrical generator. All concepts contemplated were researched to ascertain their appropriateness for the intended application. During development of the final experimental platform and after lodging of a provisional patent (RSA 2007/00927) it was ascertained that the design shared some similarities with an American patent 5503525 dated 28/4/1994. This patent employed complex electronic sensing and control equipment for control of blade angle. This was thought to be overly complex and costly, particularly for small scale wind energy generation applications and a simpler mechanical solution was sought in the design of the final experimental platform used in this project. The design of the mechanical control system was refined in an attempt to make it simpler, more durable and employ the least number of moving parts. Literature studies and patent searches conducted, suggested that the mechanical control system as developed for the final experimental platform was unique. The enormous variation in the power available from the wind at the different wind speeds likely to be encountered by the device necessitated some means of control. In high wind conditions control of the amount of wind power into the device was deemed to be the preferable means of control. A number of different concepts to achieve this were devised and tested. The final concept employed limited the tail angle deflection and hence the lift produced by the aerofoils. This resulted in a seamless “throttle” control allowing the device to be used in any wind strength by adjusting the control to a position that resulted in the device receiving a suitable amount of power from the wind. The outcome of performance tests conducted indicated that the device has the potential to be developed into a viable wind turbine for both small and large scale applications. The ability to control the power input from the wind to the machine from zero to a maximum is considered to be one of the most beneficial outcomes of this project and together with the quiet operation and low speed, are considered the main advantages of the device over existing wind turbine designs. The possibilities of using the device to compress air for energy storage are exciting avenues that warrant further research.
- Full Text:
- Date Issued: 2008
Hybrid field generator controller for optimised perfomance
- Authors: Moleli, Christopher Teboho
- Date: 2003
- Subjects: Hybrid power systems , Wind turbines , Electric power production
- Language: English
- Type: Thesis , Masters , MTech (Electrical Engineering)
- Identifier: vital:10818 , http://hdl.handle.net/10948/236 , Hybrid power systems , Wind turbines , Electric power production
- Description: Battery charging wind turbines like, Hybrid Field Generator, have become more popular in the growing renewable energy market. With wind energy, voltage and current control is generally provided by means of power electronics. The paper describes the analytical investigation in to control aspects of a hybrid field generator controller for optimized performance. The project objective is about maintaining the generated voltage at 28V through out a generator speed range, between 149 rpm and 598 rpm. The over voltage load, known as dump load, is connected to the control circuit to reduce stress on the bypass transistor for speeds above 598 rpm. Maintaining a stable voltage through out the speed range, between 149rpm and 598rpm, is achieved by employing power electronics techniques. This is done by using power converters and inverters to vary the generator armature excitation levels hence varying its air gap flux density. All these take place during each of the three modes of generator operation, which are: buck, boost and permanent magnet modes. Although the generator controller is power electronics based, it also uses software to optimize its performance. In this case, a PIC16F877 microcontroller development system has been used to test the controller function blocks.
- Full Text:
- Date Issued: 2003
- Authors: Moleli, Christopher Teboho
- Date: 2003
- Subjects: Hybrid power systems , Wind turbines , Electric power production
- Language: English
- Type: Thesis , Masters , MTech (Electrical Engineering)
- Identifier: vital:10818 , http://hdl.handle.net/10948/236 , Hybrid power systems , Wind turbines , Electric power production
- Description: Battery charging wind turbines like, Hybrid Field Generator, have become more popular in the growing renewable energy market. With wind energy, voltage and current control is generally provided by means of power electronics. The paper describes the analytical investigation in to control aspects of a hybrid field generator controller for optimized performance. The project objective is about maintaining the generated voltage at 28V through out a generator speed range, between 149 rpm and 598 rpm. The over voltage load, known as dump load, is connected to the control circuit to reduce stress on the bypass transistor for speeds above 598 rpm. Maintaining a stable voltage through out the speed range, between 149rpm and 598rpm, is achieved by employing power electronics techniques. This is done by using power converters and inverters to vary the generator armature excitation levels hence varying its air gap flux density. All these take place during each of the three modes of generator operation, which are: buck, boost and permanent magnet modes. Although the generator controller is power electronics based, it also uses software to optimize its performance. In this case, a PIC16F877 microcontroller development system has been used to test the controller function blocks.
- Full Text:
- Date Issued: 2003
- «
- ‹
- 1
- ›
- »