Investigation of brewery waste grains and microbial fuel cells as value-additive technologies improving solvent production yields in Clostridium acetobutylicum (ATCC 824) fermentation
- Authors: Du Toit, Ryan Guillaume
- Date: 2023-10-13
- Subjects: Biomass energy , Butanol , Fermentation , Microbial fuel cells , Brewery waste , Clostridium acetobutylicum
- Language: English
- Type: Academic theses , Master's theses , text
- Identifier: http://hdl.handle.net/10962/424643 , vital:72171
- Description: The production of the solvent compounds acetone, ethanol and butanol through fermentation of organic feedstocks using Clostridia species could be a promising route for biofuel production. However, the cost of raw materials, low yields and the complexity of anaerobic fermentation continue to hinder this means of generating these compounds. The research presented in this Thesis investigated low-cost interventions that could decrease the costs of production and to direct the synthesis of fuel compounds using microbial fuel cells. Low-cost anaerobic chambers were designed and constructed for the propagation and manipulation of Clostridium acetobutylicum, selected as a low-risk microbial catalyst. Fermentation was monitored using in situ pH measurements and a combination of turbidity measurements, nutrient assays (especially total carbohydrates) and HPLC-RI detection as a means of monitoring the consumption of nutrients (glucose), production of precursor compounds (butyric acid) and the formation of solvent molecules (acetone/ethanol and butanol) during fermentation by this organism. Brewer’s spent grains were tested as a sustainable and low-cost feedstock for solvent production, comparing the effects of sterilising before fermentation, or allowing resident microflora to remain during Clostridium-catalysed solvent production. Sterilised spent grains significantly improved the production of solvent molecules (e.g. 12.97 ± 0.38 g/L of butanol yielded, compared to 0.40 ± 0.33 g/L for defined media sampled during the solventogenic phase); compared to these, the use of non-sterilised brewer’s grain decreased both the reproducibility and yields of fermentation (8.66 ± 1.6 g/L of butanol). Microbial fuel cells were studied as a possible means of altering electron transfer to/from electrode-attached Clostridia to control the metabolic shift in bacteria from acidogenesis to solventogenesis. The base line MFC (11.00 ± 4.69 g/L) fermentation experiment did produce higher acetone/ethanol than the baseline batch experiment MB (5.47 ± 4.48 g/L), indicating an improvement to solvent production in C. acetobutylicum (ATCC 824) in a MFC fermentation. In this study, MFC-1 demonstrated remarkable superiority over MB in terms of butyric acid production, yielding significantly higher concentrations while also improving acetone and ethanol production. However, the enhanced butyric acid production did not correspond to significantly increased butanol yields when compared to batch fermentation of chemically defined media. These findings highlight the potential of MFC-1 as an efficient approach for enhancing the fermentative production of valuable compounds, with a particular focus on butyric acid and acetone/ethanol. , Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2023
- Full Text:
- Authors: Du Toit, Ryan Guillaume
- Date: 2023-10-13
- Subjects: Biomass energy , Butanol , Fermentation , Microbial fuel cells , Brewery waste , Clostridium acetobutylicum
- Language: English
- Type: Academic theses , Master's theses , text
- Identifier: http://hdl.handle.net/10962/424643 , vital:72171
- Description: The production of the solvent compounds acetone, ethanol and butanol through fermentation of organic feedstocks using Clostridia species could be a promising route for biofuel production. However, the cost of raw materials, low yields and the complexity of anaerobic fermentation continue to hinder this means of generating these compounds. The research presented in this Thesis investigated low-cost interventions that could decrease the costs of production and to direct the synthesis of fuel compounds using microbial fuel cells. Low-cost anaerobic chambers were designed and constructed for the propagation and manipulation of Clostridium acetobutylicum, selected as a low-risk microbial catalyst. Fermentation was monitored using in situ pH measurements and a combination of turbidity measurements, nutrient assays (especially total carbohydrates) and HPLC-RI detection as a means of monitoring the consumption of nutrients (glucose), production of precursor compounds (butyric acid) and the formation of solvent molecules (acetone/ethanol and butanol) during fermentation by this organism. Brewer’s spent grains were tested as a sustainable and low-cost feedstock for solvent production, comparing the effects of sterilising before fermentation, or allowing resident microflora to remain during Clostridium-catalysed solvent production. Sterilised spent grains significantly improved the production of solvent molecules (e.g. 12.97 ± 0.38 g/L of butanol yielded, compared to 0.40 ± 0.33 g/L for defined media sampled during the solventogenic phase); compared to these, the use of non-sterilised brewer’s grain decreased both the reproducibility and yields of fermentation (8.66 ± 1.6 g/L of butanol). Microbial fuel cells were studied as a possible means of altering electron transfer to/from electrode-attached Clostridia to control the metabolic shift in bacteria from acidogenesis to solventogenesis. The base line MFC (11.00 ± 4.69 g/L) fermentation experiment did produce higher acetone/ethanol than the baseline batch experiment MB (5.47 ± 4.48 g/L), indicating an improvement to solvent production in C. acetobutylicum (ATCC 824) in a MFC fermentation. In this study, MFC-1 demonstrated remarkable superiority over MB in terms of butyric acid production, yielding significantly higher concentrations while also improving acetone and ethanol production. However, the enhanced butyric acid production did not correspond to significantly increased butanol yields when compared to batch fermentation of chemically defined media. These findings highlight the potential of MFC-1 as an efficient approach for enhancing the fermentative production of valuable compounds, with a particular focus on butyric acid and acetone/ethanol. , Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2023
- Full Text:
Characterization of Fluorescently-Labelled Plasmodium Lactate Dehydrogenase-Binding Aptamers for the Detection and Speciation of Malarial Infections
- Authors: Taylor, Bianca Rose
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192572 , vital:45238
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
- Authors: Taylor, Bianca Rose
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192572 , vital:45238
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
Fabrication of gold-nanoparticle/conductive polymer composite materials: application to aptamer-based impedimetric biosensors for detection of histamine
- Authors: Ojo, Dupe Ruth
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192550 , vital:45236
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
- Authors: Ojo, Dupe Ruth
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192550 , vital:45236
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
Investigation of microbial fuel cell technologies for flexible, small-scale domestic and educational use
- Authors: Mpofu, Trisha Lerato
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192539 , vital:45235
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
- Authors: Mpofu, Trisha Lerato
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192539 , vital:45235
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
Photosynthetic microbial fuel cells and fabricated photobioreactors applied with halotolerant microorganisms for nutrient and metal remediation under adverse hypersaline
- Authors: Smith, Galad Gilbert
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192561 , vital:45237
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
- Authors: Smith, Galad Gilbert
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192561 , vital:45237
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
The influence of selected classes of surfactants on microbial fuel cell performance: extensive analysis of microbial activity, bioremediation and power generation for wastewater treatment
- Authors: Lipali, Molopo Johannes
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192493 , vital:45231
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
- Authors: Lipali, Molopo Johannes
- Date: 2021-10-29
- Subjects: Uncatalogued
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/192493 , vital:45231
- Description: Thesis (MSc) -- Faculty of Science, Biotechnology Innovation Centre, 2021
- Full Text:
Towards development of a malaria diagnostic: Generation, screening and validation of novel aptamers recognising Plasmodium falciparum lactate dehydrogenase
- Authors: Frith, Kelly-Anne
- Date: 2020
- Subjects: Plasmodium falciparum , Malaria -- Chemotherapy , Oligonucleotides , Lactate dehydrogenase , Biochemical markers , Systematic evolution of ligands through exponential enrichment (SELEX)
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/142247 , vital:38062
- Description: Malaria, caused by infection with the Plasmodium parasite, is one of the leading causes of death in under-developed countries. Early detection is crucial for the effective treatment of malaria, particularly in cases where infection is due to Plasmodium falciparum. There is, therefore, an enduring need for portable, sensitive, reliable, accurate, durable, self-validating and cost-effective techniques for the rapid detection of malaria. Moreover, there is a demand to distinguish between various infectious species causing malaria. Research in the area of malarial biomarkers has identified a unique, species-specific, epitope of P. falciparum lactate dehydrogenase (PfLDH), enhancing prospects for the development of diagnostics capable of identifying the species causing malarial infection. In recent years, improvements have been made towards the development of rapid diagnostic tests for detecting malarial biomarkers. Owing to their low cost, ease of labeling, and high thermal stability (relative to antibodies), the development and synthesis of aptamers that target the malarial lactate dehydrogenase represents one of the key innovations in the field of rapid diagnostics for malaria. This study explored the generation of aptamers that specifically target P. falciparum. Two sets of aptamers with diagnostically-supportive functions were generated independently, through parallel SELEX of recombinantly-expressed, full-length Plasmodium falciparum lactate dehydrogenase (rPfLDH), and an oligopeptide comprising the P. falciparum-specific epitope on lactate dehydrogenase (LDHp). The latter offers a promising solution for generating aptamers capable of binding with high specificity to P. falciparum. In this work, an rLDH class of aptamers was generated when SELEX was performed using the full-length rPfLDH protein as the target and the LDHp class of aptamers was generated when SELEX was performed using the oligopeptide LDHp as a target. Aptamers were successfully generated through the process of SELEX (systematic evolution of ligands through exponential enrichment) following the study and application of several optimisation steps, particularly during the amplification stage of SELEX. Optimisation steps included the study of improvements in PCR conditions; role of surfactants (Triton-X), modifying the PCR clean-up protocol; and agarose gel excision. Structurally-relevant moieties with particular consensus sequences (GGTAG and GGCG) were found in aptamers both reported here and previously published, confirming their importance in recognition of the target. Novel moieties particular to this work (ATTAT and poly-A stretches) were identified. Clades of consensus sequences were identified in both the rLDH and LDHp groups of aptamers, where sequences in the rLDH clade did not show preferential binding to rPfLDH while those in the LDHp clade (particularly LDHp 3 and 18) were able to recognise and bind only LDHp. Of the 19 sequences returned from the parallel SELEX procedures for rPfLDH (11 sequences) and LDHp (8 sequences), six rPfLDH and all eight LDHp sequences underwent preliminary screening and those with low responses eliminated. Of the eight LDHp-targeting aptamer sequences, five were preliminarily shown to bind to LDHp, whereas only two rPfLDH-targeting sequences were shown to bind to the target (rLDH 4 and 7). To this small selection of rPfLDH oligonucleotide sequences, two more (rLDH 1 and 15) were chosen for further study based on their sequences, secondary and predicted tertiary conformations. Sequences chosen for further study were therefore: rLDH 1, 4, 7 and 15 in the rLDH class, and LDHp 1, 3, 11, 14 and 18 in the LDHp class. Binding properties of the aptamers towards their targets were investigated using enzyme-linked oligonucleotide assays (ELONA), fluorophore-linked oligonucleotide assays (FLONA), electromobility shift assays (EMSA), surface plasmon resonance (SPR), and GelRed dissociation assays, while applications towards aptasensors were explored using electrochemical impedance spectroscopy (EIS) and fluorescent microscopy. Some inconsistencies were seen for specific aptamer to target binding interactions using specific techniques; however, generally, binding to the targets was observed across the techniques assessed. These varied responses demonstrate the need to screen and validate aptamers using a variety of techniques and platforms not necessarily specific for the proposed application. From the aptamer binding screening studies using ELONA, the most promising aptamers generated were identified as LDHp 11, rLDH 4, rLDH 7 and rLDH 15. Aptamer rLDH 4, which was generated against rPfLDH, exhibited preferential and specific binding to the lactate dehydrogenase from P. falciparum, over the recombinantly-expressed lactate dehydrogenase from Plasmodium vivax (rPvLDH), albeit with lowered responses compared to LDHp 11 in ELONA and EMSA studies. However, in kinetic ELONA studies rLDH 4 showed binding to both rPfLDH and rPvLDH. Aptamer rLDH 7 showed high affinity for rPfLDH and rPvLDH in kinetic studies using ELONA. However, screening studies with ELONA indicates that aptamer rLDH 7 may not be suitable for diagnostic tests in serum samples given its non-specific binding to human serum albumin (HSA). Aptamer rLDH 15 exhibited species specificity for rPfLDH in screening studies using ELONA but showed affinity towards rPvLDH (albeit lower relative to its affinity for rPfLDH) in kinetic studies using ELONA. LDHp 11, generated against the PfLDH peptide, showed a clear preference for rPfLDH when compared to rPvLDH and other control proteins, in both sets of ELONA studies conducted, as well as EMSA, thus possessing a strong ability to identify the presence of Plasmodium falciparum owing to its generation against the species-specific epitope. While LDHp 1 demonstrated binding to plasmodial LDH in a flow-through system (SPR), so reiterating ELONA responses, it did not perform well in the remaining methodologies. Aptamers rLDH 1 and 15 and LDHp 3, 14 and 18 exhibited a mixed set of results throughout the target protein screening analyses and were, thus, not considered for selective binding in P. falciparum parasite bodies. In studies aimed at exploring biosensor assemblies utilising the developed aptamers, both rLDH 4 and LDHp 11, along with rLDH 7, LDHp 1 and pL1, demonstrated in situ binding to the native PfLDH in fluorescent microscopy. LDHp 11 exhibited FITC-based fluorescence equivalent to the anti-rPfLDHp IgY antibody in confocal fluorescent microscopy indicating superior binding to the native PfLDH compared to the remaining aptamers. An examination of electrochemical impedance as a platform for a biosensor assembly did not, in these studies, exhibit the required sensitivity using physiologically relevant concentrations of analyte expected for pLDH following infection with Plasmodium spp. Malstat/LDH activity was explored for application in a colorimetric aptasensor. A decrease in both rPfLDH and rPvLDH activity was observed following incubation with the tested aptamers, but rLDH 1, rLDH 7 and LDHp 14 did not exhibit similar decreases in rPvLDH activity. Aptamers rLDH 1, 4 and 7 and LDHp 11 and 14 were, therefore, not selected as candidates for LDH capture in LDH activity-based diagnostic devices for P. falciparum. The decreases in pLDH activity in the presence of aptamers could hold promise as direct or antagonistic malaria therapeutic agents. Preliminary studies on the application of aptamers as malaria therapeutic agents, while of interest, should be viewed with due caution given the challenges of aptamers reaching the intracellular native plasmodial LDH hosted within the red blood cells. In conclusion, this work has shown the ability of the LDHp 11 aptamer, generated in these studies, to selectively bind rPfLDH over rPvLDH, and to bind to the native PfLDH in fluorescent microscopy, indicating that this aptamer holds promise as a biorecognition element in malaria biosensors and other diagnostic devices for the detection, and differentiation, of P. falciparum and P. vivax. The use of a species-specific epitope of P. falciparum as a target in aptamer generation paves the way for similar such studies aimed at generating aptamers with species selectivity for other Plasmodium species.
- Full Text:
- Authors: Frith, Kelly-Anne
- Date: 2020
- Subjects: Plasmodium falciparum , Malaria -- Chemotherapy , Oligonucleotides , Lactate dehydrogenase , Biochemical markers , Systematic evolution of ligands through exponential enrichment (SELEX)
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/142247 , vital:38062
- Description: Malaria, caused by infection with the Plasmodium parasite, is one of the leading causes of death in under-developed countries. Early detection is crucial for the effective treatment of malaria, particularly in cases where infection is due to Plasmodium falciparum. There is, therefore, an enduring need for portable, sensitive, reliable, accurate, durable, self-validating and cost-effective techniques for the rapid detection of malaria. Moreover, there is a demand to distinguish between various infectious species causing malaria. Research in the area of malarial biomarkers has identified a unique, species-specific, epitope of P. falciparum lactate dehydrogenase (PfLDH), enhancing prospects for the development of diagnostics capable of identifying the species causing malarial infection. In recent years, improvements have been made towards the development of rapid diagnostic tests for detecting malarial biomarkers. Owing to their low cost, ease of labeling, and high thermal stability (relative to antibodies), the development and synthesis of aptamers that target the malarial lactate dehydrogenase represents one of the key innovations in the field of rapid diagnostics for malaria. This study explored the generation of aptamers that specifically target P. falciparum. Two sets of aptamers with diagnostically-supportive functions were generated independently, through parallel SELEX of recombinantly-expressed, full-length Plasmodium falciparum lactate dehydrogenase (rPfLDH), and an oligopeptide comprising the P. falciparum-specific epitope on lactate dehydrogenase (LDHp). The latter offers a promising solution for generating aptamers capable of binding with high specificity to P. falciparum. In this work, an rLDH class of aptamers was generated when SELEX was performed using the full-length rPfLDH protein as the target and the LDHp class of aptamers was generated when SELEX was performed using the oligopeptide LDHp as a target. Aptamers were successfully generated through the process of SELEX (systematic evolution of ligands through exponential enrichment) following the study and application of several optimisation steps, particularly during the amplification stage of SELEX. Optimisation steps included the study of improvements in PCR conditions; role of surfactants (Triton-X), modifying the PCR clean-up protocol; and agarose gel excision. Structurally-relevant moieties with particular consensus sequences (GGTAG and GGCG) were found in aptamers both reported here and previously published, confirming their importance in recognition of the target. Novel moieties particular to this work (ATTAT and poly-A stretches) were identified. Clades of consensus sequences were identified in both the rLDH and LDHp groups of aptamers, where sequences in the rLDH clade did not show preferential binding to rPfLDH while those in the LDHp clade (particularly LDHp 3 and 18) were able to recognise and bind only LDHp. Of the 19 sequences returned from the parallel SELEX procedures for rPfLDH (11 sequences) and LDHp (8 sequences), six rPfLDH and all eight LDHp sequences underwent preliminary screening and those with low responses eliminated. Of the eight LDHp-targeting aptamer sequences, five were preliminarily shown to bind to LDHp, whereas only two rPfLDH-targeting sequences were shown to bind to the target (rLDH 4 and 7). To this small selection of rPfLDH oligonucleotide sequences, two more (rLDH 1 and 15) were chosen for further study based on their sequences, secondary and predicted tertiary conformations. Sequences chosen for further study were therefore: rLDH 1, 4, 7 and 15 in the rLDH class, and LDHp 1, 3, 11, 14 and 18 in the LDHp class. Binding properties of the aptamers towards their targets were investigated using enzyme-linked oligonucleotide assays (ELONA), fluorophore-linked oligonucleotide assays (FLONA), electromobility shift assays (EMSA), surface plasmon resonance (SPR), and GelRed dissociation assays, while applications towards aptasensors were explored using electrochemical impedance spectroscopy (EIS) and fluorescent microscopy. Some inconsistencies were seen for specific aptamer to target binding interactions using specific techniques; however, generally, binding to the targets was observed across the techniques assessed. These varied responses demonstrate the need to screen and validate aptamers using a variety of techniques and platforms not necessarily specific for the proposed application. From the aptamer binding screening studies using ELONA, the most promising aptamers generated were identified as LDHp 11, rLDH 4, rLDH 7 and rLDH 15. Aptamer rLDH 4, which was generated against rPfLDH, exhibited preferential and specific binding to the lactate dehydrogenase from P. falciparum, over the recombinantly-expressed lactate dehydrogenase from Plasmodium vivax (rPvLDH), albeit with lowered responses compared to LDHp 11 in ELONA and EMSA studies. However, in kinetic ELONA studies rLDH 4 showed binding to both rPfLDH and rPvLDH. Aptamer rLDH 7 showed high affinity for rPfLDH and rPvLDH in kinetic studies using ELONA. However, screening studies with ELONA indicates that aptamer rLDH 7 may not be suitable for diagnostic tests in serum samples given its non-specific binding to human serum albumin (HSA). Aptamer rLDH 15 exhibited species specificity for rPfLDH in screening studies using ELONA but showed affinity towards rPvLDH (albeit lower relative to its affinity for rPfLDH) in kinetic studies using ELONA. LDHp 11, generated against the PfLDH peptide, showed a clear preference for rPfLDH when compared to rPvLDH and other control proteins, in both sets of ELONA studies conducted, as well as EMSA, thus possessing a strong ability to identify the presence of Plasmodium falciparum owing to its generation against the species-specific epitope. While LDHp 1 demonstrated binding to plasmodial LDH in a flow-through system (SPR), so reiterating ELONA responses, it did not perform well in the remaining methodologies. Aptamers rLDH 1 and 15 and LDHp 3, 14 and 18 exhibited a mixed set of results throughout the target protein screening analyses and were, thus, not considered for selective binding in P. falciparum parasite bodies. In studies aimed at exploring biosensor assemblies utilising the developed aptamers, both rLDH 4 and LDHp 11, along with rLDH 7, LDHp 1 and pL1, demonstrated in situ binding to the native PfLDH in fluorescent microscopy. LDHp 11 exhibited FITC-based fluorescence equivalent to the anti-rPfLDHp IgY antibody in confocal fluorescent microscopy indicating superior binding to the native PfLDH compared to the remaining aptamers. An examination of electrochemical impedance as a platform for a biosensor assembly did not, in these studies, exhibit the required sensitivity using physiologically relevant concentrations of analyte expected for pLDH following infection with Plasmodium spp. Malstat/LDH activity was explored for application in a colorimetric aptasensor. A decrease in both rPfLDH and rPvLDH activity was observed following incubation with the tested aptamers, but rLDH 1, rLDH 7 and LDHp 14 did not exhibit similar decreases in rPvLDH activity. Aptamers rLDH 1, 4 and 7 and LDHp 11 and 14 were, therefore, not selected as candidates for LDH capture in LDH activity-based diagnostic devices for P. falciparum. The decreases in pLDH activity in the presence of aptamers could hold promise as direct or antagonistic malaria therapeutic agents. Preliminary studies on the application of aptamers as malaria therapeutic agents, while of interest, should be viewed with due caution given the challenges of aptamers reaching the intracellular native plasmodial LDH hosted within the red blood cells. In conclusion, this work has shown the ability of the LDHp 11 aptamer, generated in these studies, to selectively bind rPfLDH over rPvLDH, and to bind to the native PfLDH in fluorescent microscopy, indicating that this aptamer holds promise as a biorecognition element in malaria biosensors and other diagnostic devices for the detection, and differentiation, of P. falciparum and P. vivax. The use of a species-specific epitope of P. falciparum as a target in aptamer generation paves the way for similar such studies aimed at generating aptamers with species selectivity for other Plasmodium species.
- Full Text:
Exploration of challenges in bringing traditional medicine into SA’s healthcare system, using medicinal plants for treatment of waterborne diarrhoeal diseases as a case study
- Authors: Keche, Priscilla
- Date: 2019
- Subjects: Traditional medicine -- South Africa , Waterborne infection -- South Africa , Diarrhea -- South Africa , Healers -- South Africa , Medical care -- Quality control , Medicinal plants -- South Africa , Diarrhea in children -- South Africa , World Health Organization
- Language: English
- Type: thesis , text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/118035 , vital:34588
- Description: Thesis (MSc)--Rhodes University, Faculty of Science, Biotechnology Innovation Centre (RUBIC), 2019.
- Full Text:
- Authors: Keche, Priscilla
- Date: 2019
- Subjects: Traditional medicine -- South Africa , Waterborne infection -- South Africa , Diarrhea -- South Africa , Healers -- South Africa , Medical care -- Quality control , Medicinal plants -- South Africa , Diarrhea in children -- South Africa , World Health Organization
- Language: English
- Type: thesis , text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/118035 , vital:34588
- Description: Thesis (MSc)--Rhodes University, Faculty of Science, Biotechnology Innovation Centre (RUBIC), 2019.
- Full Text:
Discovery and validation of a CD4 binding aptamer through Crossover SELEX towards the preliminary development of a point-of-care aptasensor for rapid CD4+ T-cell counting
- Authors: Fellows, Tamika
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/63527 , vital:28431
- Description: Expected release date-April 2020
- Full Text:
- Authors: Fellows, Tamika
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/63527 , vital:28431
- Description: Expected release date-April 2020
- Full Text:
Key considerations for novel aptamer generation and aptasensor platform design: a case study on human α-thrombin and histamine as sensor targets
- Authors: Ho, Lance St John
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/63534 , vital:28432
- Description: Expected release date-April 2020
- Full Text:
- Authors: Ho, Lance St John
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/63534 , vital:28432
- Description: Expected release date-April 2020
- Full Text:
The current utility of oligonucleotide aptamers in targeting the MUC1 mucin tumour marker
- Authors: Flanagan, Shane Patrick
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/62969 , vital:28348
- Description: Expected release date-April 2020
- Full Text:
- Authors: Flanagan, Shane Patrick
- Date: 2018
- Subjects: Uncatalogued
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/62969 , vital:28348
- Description: Expected release date-April 2020
- Full Text:
The creation and validation of aptamers binding to murine 3T3-L1 Preadipocytes: preliminary implications for controlled cellular attachment, differentiation and cell fate
- Authors: Rubidge, Mark Lourens
- Date: 2017
- Subjects: Oligonucleotides , Fat cells , Stem cells , Ligand binding (Biochemistry) , Fluorimetry
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/65247 , vital:28714
- Description: The controlled seeding of a variety of stem cells in vitro has been reported to alter the patterns of their subsequent differentiation. This has been attributed to the control of the surface microenvironment onto which adherent stem cells are cultured, especially control of the proximal density of neighbouring cells. Simultaneously, advances in the generation of aptamers - synthetic ligand molecules developed using in vitro selection techniques targeting complex molecules - have aided in the production of molecules capable of selectively binding to a variety of commercial stem cell lines. Combining the aforementioned research fields, the project reported in this thesis aimed to generate DNA-based aptamers capable of assisting with the selective binding of murine 3T3- L1 preadipocytes to a solid surface. This was performed with a view to, eventually, control the seeding densities of the adherent preadipocytes on the surface of the tissue culture dish in subsequent researchers. In the process of meeting this goal, several optimisations of the in vitro process by which aptamers binding to cells are generated (Cell-SELEX) were performed: an analysis into a variety of methods used for the removal of the single stranded aptamer candidate sequences attached to the surface of 3T3-L1 preadipocytes, a comparison of methods for the generation of single-stranded aptamer sequences from double-stranded DNA template molecules and a method for quantifying the removed ssDNA from the cell surface. Their use is further reported in this work. Initially, it was determined that a fluorimetric evaluation of the unbound single stranded DNA was the optimum technique to use to evaluate the relative amounts of aptamer DNA binding to target cells during cell-SELEX; this arose from the release of DNA, and other cell lysate contaminates, which interfered UV/ Vis quantification. The evaluation into different methods of ssDNA removal from the cell surface showed that although trypsinisation of the cells demonstrated the highest level of aptamer detachment (quantified by fluorimetry), there is a decrease the number of potential targets that aptamers could attach to. The most common method for detaching bound DNA aptamer molecules from cellular targets reported in literature, the use of high temperatures, was selected for cell-SELEX to increase the variability in potential target sites on the cell surface. Using techniques optimised in this work, fluorescently-tagged single-stranded oligonucleotide aptamers were later generated with a positive selection pressure to bind to the surface of the 3T3-L1 preadipocytes, but not to their differentiated adipocyte counterparts. After eight cycles of cell-SELEX, fluorescent spectroscopic analysis depicted a 74 % binding retention of the selection pool in the positive preadipocyte selection pool, as opposed to a 0.69 % binding of sequences to the negative differentiated preadipocytes. Following the isolation and identification of candidate sequences, seven separate sequences were identified as being successfully generated from the selection process. Bioinformatic characterisation of these placed sequenced aptamer candidates into two separate families, that were then analysed in opposition to each for their binding affinity toward each other. Using fluorescently-tagged sequences, the binding selectivity of the generated aptamers was validated using both epifluorescent microscopy and confocal microscopy. At this stage, an aptamer sequence selected from prior in-house research to serve as a negative control also demonstrated significant binding to the extracellular matrix of both preadipocytes and mature adipocytes. 5’-thiolated aptamer sequences were used to form self-assembled monolayers on the electrode surfaces of the impedimetric Roche xCELLigence Real-Time Cell Analysis. The use of aptamer sequences to capture the seeded preadipocytes, demonstrated a slight increase in the extent of binding of the preadipocytes to the gold electrode surface and produced some preliminary indications of alterations to the pattern and rate of subsequent differentiation in the preadipocytes. This provides preliminary evidence that aptamers developed to bind specifically to a stem cell line in vitro show potential to be used as to capture said cell when cast in a self- assembled monolayer assembly. This provides a future opportunity to control the seeding densities of the cells in vitro. The effects of cellular differentiation at a set of predefined cellular densities can be demonstrated on a desired stem cell line. , Thesis (MSc) -- Faculty of Faculty of Science, Biotechnology Innovation Centre, 2017
- Full Text:
- Authors: Rubidge, Mark Lourens
- Date: 2017
- Subjects: Oligonucleotides , Fat cells , Stem cells , Ligand binding (Biochemistry) , Fluorimetry
- Language: English
- Type: Master's theses , text
- Identifier: http://hdl.handle.net/10962/65247 , vital:28714
- Description: The controlled seeding of a variety of stem cells in vitro has been reported to alter the patterns of their subsequent differentiation. This has been attributed to the control of the surface microenvironment onto which adherent stem cells are cultured, especially control of the proximal density of neighbouring cells. Simultaneously, advances in the generation of aptamers - synthetic ligand molecules developed using in vitro selection techniques targeting complex molecules - have aided in the production of molecules capable of selectively binding to a variety of commercial stem cell lines. Combining the aforementioned research fields, the project reported in this thesis aimed to generate DNA-based aptamers capable of assisting with the selective binding of murine 3T3- L1 preadipocytes to a solid surface. This was performed with a view to, eventually, control the seeding densities of the adherent preadipocytes on the surface of the tissue culture dish in subsequent researchers. In the process of meeting this goal, several optimisations of the in vitro process by which aptamers binding to cells are generated (Cell-SELEX) were performed: an analysis into a variety of methods used for the removal of the single stranded aptamer candidate sequences attached to the surface of 3T3-L1 preadipocytes, a comparison of methods for the generation of single-stranded aptamer sequences from double-stranded DNA template molecules and a method for quantifying the removed ssDNA from the cell surface. Their use is further reported in this work. Initially, it was determined that a fluorimetric evaluation of the unbound single stranded DNA was the optimum technique to use to evaluate the relative amounts of aptamer DNA binding to target cells during cell-SELEX; this arose from the release of DNA, and other cell lysate contaminates, which interfered UV/ Vis quantification. The evaluation into different methods of ssDNA removal from the cell surface showed that although trypsinisation of the cells demonstrated the highest level of aptamer detachment (quantified by fluorimetry), there is a decrease the number of potential targets that aptamers could attach to. The most common method for detaching bound DNA aptamer molecules from cellular targets reported in literature, the use of high temperatures, was selected for cell-SELEX to increase the variability in potential target sites on the cell surface. Using techniques optimised in this work, fluorescently-tagged single-stranded oligonucleotide aptamers were later generated with a positive selection pressure to bind to the surface of the 3T3-L1 preadipocytes, but not to their differentiated adipocyte counterparts. After eight cycles of cell-SELEX, fluorescent spectroscopic analysis depicted a 74 % binding retention of the selection pool in the positive preadipocyte selection pool, as opposed to a 0.69 % binding of sequences to the negative differentiated preadipocytes. Following the isolation and identification of candidate sequences, seven separate sequences were identified as being successfully generated from the selection process. Bioinformatic characterisation of these placed sequenced aptamer candidates into two separate families, that were then analysed in opposition to each for their binding affinity toward each other. Using fluorescently-tagged sequences, the binding selectivity of the generated aptamers was validated using both epifluorescent microscopy and confocal microscopy. At this stage, an aptamer sequence selected from prior in-house research to serve as a negative control also demonstrated significant binding to the extracellular matrix of both preadipocytes and mature adipocytes. 5’-thiolated aptamer sequences were used to form self-assembled monolayers on the electrode surfaces of the impedimetric Roche xCELLigence Real-Time Cell Analysis. The use of aptamer sequences to capture the seeded preadipocytes, demonstrated a slight increase in the extent of binding of the preadipocytes to the gold electrode surface and produced some preliminary indications of alterations to the pattern and rate of subsequent differentiation in the preadipocytes. This provides preliminary evidence that aptamers developed to bind specifically to a stem cell line in vitro show potential to be used as to capture said cell when cast in a self- assembled monolayer assembly. This provides a future opportunity to control the seeding densities of the cells in vitro. The effects of cellular differentiation at a set of predefined cellular densities can be demonstrated on a desired stem cell line. , Thesis (MSc) -- Faculty of Faculty of Science, Biotechnology Innovation Centre, 2017
- Full Text:
The interaction of selected bacteria with tailored electrospun fibres: towards future applications in bioremediation, bacterial inactivation and electricity generation
- Authors: Mfuku, Aphiwe
- Date: 2017
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/65123 , vital:28693
- Description: Expected release date-May 2019
- Full Text:
- Authors: Mfuku, Aphiwe
- Date: 2017
- Language: English
- Type: text , Thesis , Masters , MSc
- Identifier: http://hdl.handle.net/10962/65123 , vital:28693
- Description: Expected release date-May 2019
- Full Text:
Towards a Mobile Bioethanol Unit for point of source conversion of sugar sources to bioethanol: design and feasibility study for South Africa
- Authors: Cech, Alexandra Louise
- Date: 2015
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/59141 , vital:27439
- Description: Restricted access-thesis embargoed for 5 years
- Full Text:
- Authors: Cech, Alexandra Louise
- Date: 2015
- Language: English
- Type: text , Thesis , Doctoral , PhD
- Identifier: http://hdl.handle.net/10962/59141 , vital:27439
- Description: Restricted access-thesis embargoed for 5 years
- Full Text:
Critical studies in carbon electrode materials with applications in the electroanalysis of the mycotoxin citrinin
- Authors: Niland, Michael John
- Date: 2013
- Subjects: Electrodes, Carbon , Mycotoxins
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4555 , http://hdl.handle.net/10962/d1018256
- Description: Guided by increasing legislation, the analysis of food borne toxins, including mycotoxins, seeks to address market related demands for the development of analytical systems to monitor this threat to food security and human health. This Thesis is directed at the assessment of the application of electrochemistry for direct electroanalysis and characterisation of the mycotoxin citrinin (CIT) in aqueous media as well as fundamental investigations of the surface of polished and oxidised glassy carbon electrodes (GCE). This study provides the first known account of CIT detection through electrochemical methods. Although electrochemically active, CIT current responses (Ip) were highly irreproducible at polished GCE with a coefficient of variation (C.V.) of 20.16 %. As stability of Ip across multiple electrode preparations is a key requirement in electroanalysis, investigations were directed at attaining stability in CIT Ip. Achieving stability in CIT Ip was investigated via two approaches, including: accounting for Ip variability between electrode preparations as a result of variable GCE surface conditions as a post-data-acquisition analysis and secondly, removing Ip variability through modification of GCE. Accounting for variability in Ip was investigated through the application of double layer capacitance as an indicator of the activity of an electrode, and in so doing serving as a relative mediator of Ip responses between electrodes. Application of this procedure dropped CIT C.V. to a third of starting value across polished GCE (C.V. = 7.18 %), chemically oxidised GCE (Pi-GCE, C.V = 8.47 %) and functionalised multi-walled carbon nanotube modified GCE (fMWCNT, C.V. = 25.79 %) and was effective with analysis of structurally distinct molecules, 2,4-dimethylaniline (2,4-DMA) and 1,2,4-trihydroxybenzene (Triol). Furthermore, it afforded the ability to determine discreet solution overlapping data sets of Ip. Stabilising Ip through GCE surface modification was achieved by anodic electro-oxidation of GCE and allowed for direct electroanalysis of CIT and subsequent characterisation and analysis of CIT in complex media as it reduced C.V. of CIT Ip to 0.73 %. Fundamental investigations of the electrode surface condition are described such that the source of variability could be identified and the interactions of CIT with the electrode understood. Two surface oxidation techniques were applied in modification of GCE; anodic electro-oxidation (EOx GCE) and chemical oxidation using piranha solution (Pi-GCE), analysis of which has previously not been reported. Fundamental analyses to determine surface morphology and chemistry of Pi-GCE, EOx-GCE and polished GCE were conducted using high resolution scanning electron microscopy (HRSEM), scanning electrochemical microscopy (SECM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), fourier transform infrared spectroscopy (FTIR) and via electroanalytical methods. These studies showed that both oxidation procedures introduced a variety of oxide species at GCE surface, and further that the extent of those species was similar with total % O being 27.67 % and 33.47 % at Pi-GCE and EOx-GCE respectively. Although chemically similar, each surface was morphologically distinct. Electrochemical analyses at the surfaces revealed Pi-GCE to behave more similarly to polished GCE than EOx-GCE. As CIT responses were found to be stable at EOx-GCE (C.V. = 0.73 %) as opposed to Pi-GCE (C.V. = 22.87 %), stability of CIT Ip was likely to be as a result of a physical interaction with electrode morphology rather than interaction on a chemical basis. Morphological analyses revealed polished GCE and Pi-GCE to be highly morphologically irregular at the micro-scale. Although comparatively smooth, the surface morphology of EOx-GCE does not account for the stability of Ip. This study thus proposed a theory to describe the mechanism by which the limited conductivity and porosity of EOx-GCE allow for it to provide a relatively stable surface area within the oxide layer, adjacent to the electrode surface, and thus provided a stable platform for electroanalysis. Voltammetric characterization of CIT at EOx-GCE revealed that anodic oxidation in aqueous media involved an uneven number of electrons to protons via an ECE mechanism. This was illustrated to be nt = 2e- accompanied by the transfer of 1H⁺ per molecule oxidised. A proposed reaction scheme for the initial stages of CIT oxidation was suggested to involve both hydroxyl and carboxyl moieties of the CIT molecule. CIT oxidation was shown to arise as a result of a relatively complex mass transport regime which included both adsorptive and diffusive derived Ip₁. The LOD in buffered aqueous media was found to be 16 nM, a highly competitive result in relation to chromatographic techniques. Further application of EOx-GCE in complex media illustrated that CIT associates non-specifically with the components of food samples, primarily proteins. As a result of this, extraction of CIT from such media is mandatory. Liquid-liquid extraction illustrated a recovery in CIT Ip₁ and in so doing provided a means of accurately and sensitively detecting CIT from food samples with an LOD of 20 nM. These responses were corroborated by HPLC analyses on the same extractions and illustrate the applicability of electroanalysis as an analytical technique.
- Full Text:
- Authors: Niland, Michael John
- Date: 2013
- Subjects: Electrodes, Carbon , Mycotoxins
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4555 , http://hdl.handle.net/10962/d1018256
- Description: Guided by increasing legislation, the analysis of food borne toxins, including mycotoxins, seeks to address market related demands for the development of analytical systems to monitor this threat to food security and human health. This Thesis is directed at the assessment of the application of electrochemistry for direct electroanalysis and characterisation of the mycotoxin citrinin (CIT) in aqueous media as well as fundamental investigations of the surface of polished and oxidised glassy carbon electrodes (GCE). This study provides the first known account of CIT detection through electrochemical methods. Although electrochemically active, CIT current responses (Ip) were highly irreproducible at polished GCE with a coefficient of variation (C.V.) of 20.16 %. As stability of Ip across multiple electrode preparations is a key requirement in electroanalysis, investigations were directed at attaining stability in CIT Ip. Achieving stability in CIT Ip was investigated via two approaches, including: accounting for Ip variability between electrode preparations as a result of variable GCE surface conditions as a post-data-acquisition analysis and secondly, removing Ip variability through modification of GCE. Accounting for variability in Ip was investigated through the application of double layer capacitance as an indicator of the activity of an electrode, and in so doing serving as a relative mediator of Ip responses between electrodes. Application of this procedure dropped CIT C.V. to a third of starting value across polished GCE (C.V. = 7.18 %), chemically oxidised GCE (Pi-GCE, C.V = 8.47 %) and functionalised multi-walled carbon nanotube modified GCE (fMWCNT, C.V. = 25.79 %) and was effective with analysis of structurally distinct molecules, 2,4-dimethylaniline (2,4-DMA) and 1,2,4-trihydroxybenzene (Triol). Furthermore, it afforded the ability to determine discreet solution overlapping data sets of Ip. Stabilising Ip through GCE surface modification was achieved by anodic electro-oxidation of GCE and allowed for direct electroanalysis of CIT and subsequent characterisation and analysis of CIT in complex media as it reduced C.V. of CIT Ip to 0.73 %. Fundamental investigations of the electrode surface condition are described such that the source of variability could be identified and the interactions of CIT with the electrode understood. Two surface oxidation techniques were applied in modification of GCE; anodic electro-oxidation (EOx GCE) and chemical oxidation using piranha solution (Pi-GCE), analysis of which has previously not been reported. Fundamental analyses to determine surface morphology and chemistry of Pi-GCE, EOx-GCE and polished GCE were conducted using high resolution scanning electron microscopy (HRSEM), scanning electrochemical microscopy (SECM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), fourier transform infrared spectroscopy (FTIR) and via electroanalytical methods. These studies showed that both oxidation procedures introduced a variety of oxide species at GCE surface, and further that the extent of those species was similar with total % O being 27.67 % and 33.47 % at Pi-GCE and EOx-GCE respectively. Although chemically similar, each surface was morphologically distinct. Electrochemical analyses at the surfaces revealed Pi-GCE to behave more similarly to polished GCE than EOx-GCE. As CIT responses were found to be stable at EOx-GCE (C.V. = 0.73 %) as opposed to Pi-GCE (C.V. = 22.87 %), stability of CIT Ip was likely to be as a result of a physical interaction with electrode morphology rather than interaction on a chemical basis. Morphological analyses revealed polished GCE and Pi-GCE to be highly morphologically irregular at the micro-scale. Although comparatively smooth, the surface morphology of EOx-GCE does not account for the stability of Ip. This study thus proposed a theory to describe the mechanism by which the limited conductivity and porosity of EOx-GCE allow for it to provide a relatively stable surface area within the oxide layer, adjacent to the electrode surface, and thus provided a stable platform for electroanalysis. Voltammetric characterization of CIT at EOx-GCE revealed that anodic oxidation in aqueous media involved an uneven number of electrons to protons via an ECE mechanism. This was illustrated to be nt = 2e- accompanied by the transfer of 1H⁺ per molecule oxidised. A proposed reaction scheme for the initial stages of CIT oxidation was suggested to involve both hydroxyl and carboxyl moieties of the CIT molecule. CIT oxidation was shown to arise as a result of a relatively complex mass transport regime which included both adsorptive and diffusive derived Ip₁. The LOD in buffered aqueous media was found to be 16 nM, a highly competitive result in relation to chromatographic techniques. Further application of EOx-GCE in complex media illustrated that CIT associates non-specifically with the components of food samples, primarily proteins. As a result of this, extraction of CIT from such media is mandatory. Liquid-liquid extraction illustrated a recovery in CIT Ip₁ and in so doing provided a means of accurately and sensitively detecting CIT from food samples with an LOD of 20 nM. These responses were corroborated by HPLC analyses on the same extractions and illustrate the applicability of electroanalysis as an analytical technique.
- Full Text:
Application of catalysts and nanomaterials in the design of an electrochemical sensor for ochratoxin A
- Authors: Flanagan, Shane Patrick
- Date: 2011 , 2010-12-06
- Subjects: Ochratoxins , Filamentous fungi , Electrochemical sensors , Nanostructured materials , Catalysts , Food contamination
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4121 , http://hdl.handle.net/10962/d1013328
- Description: Ochratoxin A is the most potent chlorinated derivative of the ochratoxin group, consisting of a 5'-chlorinated dihydroisocoumarin moiety linked by an amide bond to l-phenylalanine. Produced as a secondary fungal metabolite by several species of Aspergillus and Penicillium, ochratoxin A has been shown to readily contaminate a large variety of commodities including cereals, groundnuts, dried fruit, spices and coffee. This has led to widespread contamination of ochratoxin in wine, beer, milk and meat products. As ochratoxin A is a potent nephrotoxin exhibiting teratogenic and carcinogenic properties, the development of a rapid screening platform for the cost effective control of ochratoxin A content in foodstuffs is therefore required. The evaluation of metallophthalocyanine and carbon nanotube electrode modification toward the development of a nanostructured biosensor capable of enhancing the electrochemical detection of ochratoxin A in complex media is presented. Cyclic voltammetry at a glassy carbon electrode allowed for the optimization of detection parameters including pH and type of supporting electrolyte. Britton-Robinson buffer was found to be the most suitable supporting electrolyte in terms of sensitivity and reproducibility obtaining a LOD of 0.28 μM as determined by differential pulse voltammetry. Subsequent analysis determined the dependence of OTA oxidation on pH in acidic media which proceeds with the transfer of two electrons to form a quinone/hydroquinone couple shown to adsorb to the electrode surface. Passivation of the electrode through adsorption of oxidation products was shown to severely limit the detection of OTA upon successive detection cycles. Comparison of various metallophthalocyanine modifiers showed an increase in sensitivity toward the detection of OTA at phthalocyanine complexes with metal based redox processes. However with the exception of NiPc and CoTCPc complexes, phthalocyanine modification was limited by the increase in deviation of current response and extent of fouling. NiPc modification showed an increase in sensitivity by two fold with fouling characteristics comparable to an unmodified electrode while low improvements in fouling was observed at CoTCPc modified electrodes with sensitivity in detection comparable to an unmodified electrode.Modification of the electrode with multi- and single walled carbon nanotubes produced a significant increase in sensitivity toward the detection of ochratoxin A. The electrocatalytic activity of nanotube modifiers was attributed to the increase in surface area and to the addition of oxygenated functional groups upon acid treatment as confirmed by Raman spectroscopy. Acid functionalization of the carbon nanotubes for a period of two hours produced the greatest increase in sensitivity obtaining a respective LOD of 0.09 μM and 0.03 μM for analysis of ochratoxin A at multi- and single walled carbon nanotube modified electrodes. Centrifugal purification of carbon nanotubes was deemed necessary to improve the electrocatalytic activity of the nanotube modifiers through the removal of carbonaceous impurities as visualized by atomic force microscopy. Furthermore, a crude lipase preparation, lipase A, was investigated as a potential biological recognition element for selective detection of ochratoxin A in complex media. Lipase A enabled the hydrolysis of ochratoxin A to the electroactive species ochratoxin α as confirmed by thin layer chromatography and voltammetric analysis. Additional isolation of a pure hydrolase from the lipase A preparation is required prior to utilization within a nanostructured biosensor platform capable of detecting ochratoxin A in complex media.
- Full Text:
- Authors: Flanagan, Shane Patrick
- Date: 2011 , 2010-12-06
- Subjects: Ochratoxins , Filamentous fungi , Electrochemical sensors , Nanostructured materials , Catalysts , Food contamination
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4121 , http://hdl.handle.net/10962/d1013328
- Description: Ochratoxin A is the most potent chlorinated derivative of the ochratoxin group, consisting of a 5'-chlorinated dihydroisocoumarin moiety linked by an amide bond to l-phenylalanine. Produced as a secondary fungal metabolite by several species of Aspergillus and Penicillium, ochratoxin A has been shown to readily contaminate a large variety of commodities including cereals, groundnuts, dried fruit, spices and coffee. This has led to widespread contamination of ochratoxin in wine, beer, milk and meat products. As ochratoxin A is a potent nephrotoxin exhibiting teratogenic and carcinogenic properties, the development of a rapid screening platform for the cost effective control of ochratoxin A content in foodstuffs is therefore required. The evaluation of metallophthalocyanine and carbon nanotube electrode modification toward the development of a nanostructured biosensor capable of enhancing the electrochemical detection of ochratoxin A in complex media is presented. Cyclic voltammetry at a glassy carbon electrode allowed for the optimization of detection parameters including pH and type of supporting electrolyte. Britton-Robinson buffer was found to be the most suitable supporting electrolyte in terms of sensitivity and reproducibility obtaining a LOD of 0.28 μM as determined by differential pulse voltammetry. Subsequent analysis determined the dependence of OTA oxidation on pH in acidic media which proceeds with the transfer of two electrons to form a quinone/hydroquinone couple shown to adsorb to the electrode surface. Passivation of the electrode through adsorption of oxidation products was shown to severely limit the detection of OTA upon successive detection cycles. Comparison of various metallophthalocyanine modifiers showed an increase in sensitivity toward the detection of OTA at phthalocyanine complexes with metal based redox processes. However with the exception of NiPc and CoTCPc complexes, phthalocyanine modification was limited by the increase in deviation of current response and extent of fouling. NiPc modification showed an increase in sensitivity by two fold with fouling characteristics comparable to an unmodified electrode while low improvements in fouling was observed at CoTCPc modified electrodes with sensitivity in detection comparable to an unmodified electrode.Modification of the electrode with multi- and single walled carbon nanotubes produced a significant increase in sensitivity toward the detection of ochratoxin A. The electrocatalytic activity of nanotube modifiers was attributed to the increase in surface area and to the addition of oxygenated functional groups upon acid treatment as confirmed by Raman spectroscopy. Acid functionalization of the carbon nanotubes for a period of two hours produced the greatest increase in sensitivity obtaining a respective LOD of 0.09 μM and 0.03 μM for analysis of ochratoxin A at multi- and single walled carbon nanotube modified electrodes. Centrifugal purification of carbon nanotubes was deemed necessary to improve the electrocatalytic activity of the nanotube modifiers through the removal of carbonaceous impurities as visualized by atomic force microscopy. Furthermore, a crude lipase preparation, lipase A, was investigated as a potential biological recognition element for selective detection of ochratoxin A in complex media. Lipase A enabled the hydrolysis of ochratoxin A to the electroactive species ochratoxin α as confirmed by thin layer chromatography and voltammetric analysis. Additional isolation of a pure hydrolase from the lipase A preparation is required prior to utilization within a nanostructured biosensor platform capable of detecting ochratoxin A in complex media.
- Full Text:
Fundamental investigations into the factors affecting the response of laccase-based electrochemical biosensors
- Authors: Fogel, Ronen
- Date: 2011
- Subjects: Laccase Phenols Biosensors
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4073 , http://hdl.handle.net/10962/d1007166
- Description: Given their widespread effects and distribution in both natural and industrial environments, the monitoring of phenolic compounds is of considerable analytical interest. Electrochemical biosensor technologies, in particular those comprising laccase enzymes, afford many potential benefits to address this analytical need. However, several key factors affecting sensor response currently limit their applicability. This Thesis reports on the fabrication and optimisation of an electrochemical laccase-based biosensor towards the application of the monitoring of phenolic compounds. Selected factors considered to affect sensor response were investigated using the optimised biosensor. These included: electrochemical, biochemical and substrate-dependent factors, which were found to intersect in modulating biosensor response signals. Through the application of transducer-dependent and substrate-dependent parameters, the selective and simultaneous detection of a mixture of different phenolic analytes is successfully demonstrated. This Thesis also investigates the use of Quartz-Crystal Microbalance with Dissipation (QCM-D) technology, an analytical technique that measures physical parameters of thin-film structures, towards the successful monitoring of enzyme immobilisation strategies. These strategies are fundamental to the successful fabrication of biosensors, and the real-time monitoring of immobilised film formations is of considerable research interest. In the studies reported on in this Thesis, QCM-D technology was demonstrated to be an effective complementary technology in the prediction of film immobilisation techniques on the resultant biochemical kinetics of immobilised enzymes.
- Full Text:
- Authors: Fogel, Ronen
- Date: 2011
- Subjects: Laccase Phenols Biosensors
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4073 , http://hdl.handle.net/10962/d1007166
- Description: Given their widespread effects and distribution in both natural and industrial environments, the monitoring of phenolic compounds is of considerable analytical interest. Electrochemical biosensor technologies, in particular those comprising laccase enzymes, afford many potential benefits to address this analytical need. However, several key factors affecting sensor response currently limit their applicability. This Thesis reports on the fabrication and optimisation of an electrochemical laccase-based biosensor towards the application of the monitoring of phenolic compounds. Selected factors considered to affect sensor response were investigated using the optimised biosensor. These included: electrochemical, biochemical and substrate-dependent factors, which were found to intersect in modulating biosensor response signals. Through the application of transducer-dependent and substrate-dependent parameters, the selective and simultaneous detection of a mixture of different phenolic analytes is successfully demonstrated. This Thesis also investigates the use of Quartz-Crystal Microbalance with Dissipation (QCM-D) technology, an analytical technique that measures physical parameters of thin-film structures, towards the successful monitoring of enzyme immobilisation strategies. These strategies are fundamental to the successful fabrication of biosensors, and the real-time monitoring of immobilised film formations is of considerable research interest. In the studies reported on in this Thesis, QCM-D technology was demonstrated to be an effective complementary technology in the prediction of film immobilisation techniques on the resultant biochemical kinetics of immobilised enzymes.
- Full Text:
Nanomaterial modified electrodes : optimization of voltammetric sensors for pharmaceutical and industrial application
- Authors: Brimecombe, Rory Dennis
- Date: 2011
- Subjects: Voltammetry , Electrochemistry , Nanotubes , Nanostructured materials
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4101 , http://hdl.handle.net/10962/d1009721
- Description: Nanomaterials, in particular carbon nanotubes have been shown to exhibit favourable properties for the enhancement of electrochemical detection of target analytes in complex matrices. There is however scope for improvement in terms of the optimization thereof in electrochemical sensors surface modification. The aim of this thesis was to examine methods that would result in increased current response, lowered passivation and application of such modified surfaces with application to pharmaceutically and industrially relevant analytes. Current methods for enhancing the performance of carbon nanotubes include acid functionalization which not only increases the hydrophilicity of the nanotubes, and consequently their ability to provide stable (aqueous) suspensions, but also introduces electrochemically active sites. This particular approach is however not normalized in the literature. Over-exposure to acid treatment results in loss of structural integrity of the carbon nanotubes, and as such a fine balance exists between achieving these dual outcomes. Guided by high resolution scanning electron microscopy, atomic force microscopy, voltammetric and impedance studies, this thesis examined the role of the length of time of the acid functionalization process as well as the impact of activation of carbon nanotubes and fullerenes on electrochemical sensor performance. Based on desired charge transfer resistances, rate transfer coefficients and sensitivity towards redox probes the optimal length of acid functionalization for multiwalled carbon nanotubes was 9 hours and 4 hours for single-walled carbon nanotubes. Further improvements in the desired outcomes were achieved through electrochemical activation of the modified electrode surface by cycling in the presence of catechol, in a novel approach. By employing electrochemical impedance spectroscopy it was observed that catechol activation resulted in lowered charge transfer resistance, before and after activation, with functionalized multi-walled carbon nanotubes (9 hours) exhibiting the greatest decrease of 90 % and functionalized single-walled carbon nanotubes (4 hours), a 50 % decrease. Corresponding increases in the heterologous rate transfer coefficient showed a 770 % increase for functionalized multi-walled carbon nanotubes (9 hours), following catechol activation. Comparative observations for fullerenes following partial reduction in potassium hydroxide yielded a 30 % decrease in charge transfer resistance, with an increased heterologous rate transfer coefficient at a fullerene modified surface The performance of the nanomaterial modified electrodes was applied to the detection of wortmannin with applications in bioprocess control and in the pharmaceutical sector as well as to the detection and monitoring of the industrial dye Reactive red. Of particular relevance to these analytes was the assessment of the nanomaterial modified electrodes for enhanced stability, reproducibility, sensitivity and decreased passivation effects. In this study the first known account of wortmannin detection through electrochemical methods is reported. Voltammetric characterization of wortmannin revealed an irreversible cathodic process with a total number of 4 electrons and a diffusion coefficient of 1.19 x 10-7 cm².s⁻¹. At a functionalized multiwalled carbon nanotubes modified glassy carbon electrode a limit of detection of 0.128 nmol.cm⁻³ was obtained, and with limited surface passivation the detection scheme afforded pertinent analyses in biological media representing a substantial improvement over chromatographic detection methods. This study also provided the first account of the voltammetric detection of reactive red, competing favourably with traditional spectroscopic methods for monitoring biodegradation of this compound in real time.
- Full Text:
- Authors: Brimecombe, Rory Dennis
- Date: 2011
- Subjects: Voltammetry , Electrochemistry , Nanotubes , Nanostructured materials
- Language: English
- Type: Thesis , Doctoral , PhD
- Identifier: vital:4101 , http://hdl.handle.net/10962/d1009721
- Description: Nanomaterials, in particular carbon nanotubes have been shown to exhibit favourable properties for the enhancement of electrochemical detection of target analytes in complex matrices. There is however scope for improvement in terms of the optimization thereof in electrochemical sensors surface modification. The aim of this thesis was to examine methods that would result in increased current response, lowered passivation and application of such modified surfaces with application to pharmaceutically and industrially relevant analytes. Current methods for enhancing the performance of carbon nanotubes include acid functionalization which not only increases the hydrophilicity of the nanotubes, and consequently their ability to provide stable (aqueous) suspensions, but also introduces electrochemically active sites. This particular approach is however not normalized in the literature. Over-exposure to acid treatment results in loss of structural integrity of the carbon nanotubes, and as such a fine balance exists between achieving these dual outcomes. Guided by high resolution scanning electron microscopy, atomic force microscopy, voltammetric and impedance studies, this thesis examined the role of the length of time of the acid functionalization process as well as the impact of activation of carbon nanotubes and fullerenes on electrochemical sensor performance. Based on desired charge transfer resistances, rate transfer coefficients and sensitivity towards redox probes the optimal length of acid functionalization for multiwalled carbon nanotubes was 9 hours and 4 hours for single-walled carbon nanotubes. Further improvements in the desired outcomes were achieved through electrochemical activation of the modified electrode surface by cycling in the presence of catechol, in a novel approach. By employing electrochemical impedance spectroscopy it was observed that catechol activation resulted in lowered charge transfer resistance, before and after activation, with functionalized multi-walled carbon nanotubes (9 hours) exhibiting the greatest decrease of 90 % and functionalized single-walled carbon nanotubes (4 hours), a 50 % decrease. Corresponding increases in the heterologous rate transfer coefficient showed a 770 % increase for functionalized multi-walled carbon nanotubes (9 hours), following catechol activation. Comparative observations for fullerenes following partial reduction in potassium hydroxide yielded a 30 % decrease in charge transfer resistance, with an increased heterologous rate transfer coefficient at a fullerene modified surface The performance of the nanomaterial modified electrodes was applied to the detection of wortmannin with applications in bioprocess control and in the pharmaceutical sector as well as to the detection and monitoring of the industrial dye Reactive red. Of particular relevance to these analytes was the assessment of the nanomaterial modified electrodes for enhanced stability, reproducibility, sensitivity and decreased passivation effects. In this study the first known account of wortmannin detection through electrochemical methods is reported. Voltammetric characterization of wortmannin revealed an irreversible cathodic process with a total number of 4 electrons and a diffusion coefficient of 1.19 x 10-7 cm².s⁻¹. At a functionalized multiwalled carbon nanotubes modified glassy carbon electrode a limit of detection of 0.128 nmol.cm⁻³ was obtained, and with limited surface passivation the detection scheme afforded pertinent analyses in biological media representing a substantial improvement over chromatographic detection methods. This study also provided the first account of the voltammetric detection of reactive red, competing favourably with traditional spectroscopic methods for monitoring biodegradation of this compound in real time.
- Full Text:
Nanostructures and metallophthalocyanines : applications in microbial fuel cells
- Authors: Edwards, Sean
- Date: 2011
- Subjects: Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4107 , http://hdl.handle.net/10962/d1011742 , Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Description: Microbial fuel cells (MFCs) are a promising form of alternative energy capable of harnessing the potential energy stores in organic waste. The oxygen reduction reaction (ORR) forms an integral role in the generation of electricity in MFCs however it is also a potential obstacle in enhancing the performance of MFCs. Platinum, a commonly used catalyst for the ORR, is expensive and rare. Significant research has been conducted into developing alternative catalysts. Metallophthalocyanines (MPc) have garnered attention for use as catalysts. Iron phthalocyanine (FePc) has been shown to have catalytic activity towards the reduction of oxygen. Coupling of the catalyst to nanostructured carbon materials, such as multi-walled carbon nanotubes, has been observed to have several advantages as nanostructures have a high surface-to-volume ratio. In this study, we have attempted to assess the suitability of FePc, both its bulk and nanostructured form, as an oxygen reduction catalyst and acid functionalized multi-walled carbon nanotubes for use as a catalyst support using electrochemical techniques such as cyclic voltammetry and electrochemical impedance spectroscopy. We showed, for the first time, the catalytic nature of nanostructured FePc towards the ORR. Applying the data obtained from the electrochemical analyses, electrodes were modified using FePc and MWCNTs and applied to an Enterobacter cloacae-based MFC. Several operational parameters of the MFC, such as temperature and ionic strength, were optimized during the course of the study. We showed that optimized FePc:MWCNT-modified electrodes compared favourably to platinum-based electrodes in terms of power densities obtained in a microbial fuel cell.
- Full Text:
- Authors: Edwards, Sean
- Date: 2011
- Subjects: Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4107 , http://hdl.handle.net/10962/d1011742 , Microbial fuel cells , Waste products as fuel , Nanostructured materials , Electrochemistry , Nanotubes
- Description: Microbial fuel cells (MFCs) are a promising form of alternative energy capable of harnessing the potential energy stores in organic waste. The oxygen reduction reaction (ORR) forms an integral role in the generation of electricity in MFCs however it is also a potential obstacle in enhancing the performance of MFCs. Platinum, a commonly used catalyst for the ORR, is expensive and rare. Significant research has been conducted into developing alternative catalysts. Metallophthalocyanines (MPc) have garnered attention for use as catalysts. Iron phthalocyanine (FePc) has been shown to have catalytic activity towards the reduction of oxygen. Coupling of the catalyst to nanostructured carbon materials, such as multi-walled carbon nanotubes, has been observed to have several advantages as nanostructures have a high surface-to-volume ratio. In this study, we have attempted to assess the suitability of FePc, both its bulk and nanostructured form, as an oxygen reduction catalyst and acid functionalized multi-walled carbon nanotubes for use as a catalyst support using electrochemical techniques such as cyclic voltammetry and electrochemical impedance spectroscopy. We showed, for the first time, the catalytic nature of nanostructured FePc towards the ORR. Applying the data obtained from the electrochemical analyses, electrodes were modified using FePc and MWCNTs and applied to an Enterobacter cloacae-based MFC. Several operational parameters of the MFC, such as temperature and ionic strength, were optimized during the course of the study. We showed that optimized FePc:MWCNT-modified electrodes compared favourably to platinum-based electrodes in terms of power densities obtained in a microbial fuel cell.
- Full Text:
Probing the biocompatibility of biomedical interfaces using the Quartz Crystal Microbalance with Dissipation
- Authors: Cromhout, Mary
- Date: 2011
- Subjects: Biomedical materials , Nanostructured materials , Biomedical engineering , Quartz crystal microbalances , Blood proteins , Nanoparticles
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4102 , http://hdl.handle.net/10962/d1010660
- Description: The biomedical application of nanotechnology has come into the spotlight, with the promise of ‘personalised’ therapeutics that couple early diagnosis with targeted therapeutic activity. Due to the rapid growth of the biomedical applications of nanoparticles, along with the lack of understanding concerning their interactions with biomolecules, there is a pressing need for the development of standard methods directed at investigating the effect of introducing these unique particles into the human body. The central aim of this research is to establish a platform directed at assessing the biological fate of pioneering therapeutic particulate agents, such as metallophthalocyanines (MPcs) and multi-walled carbon nanotubes (FMWCNTs). In particular, we proposed, that Quartz Crystal Microbalance with Dissipation (QCM-D) technology may be employed to assess the composition of blood protein corona deposited on the therapeutic surface, and subsequently assess the biocompatibility of such particles. The proposed method of protein detection utilises the nanogram sensitivity of QCM-D technology to monitor highly specific antibody-antigen interactions. In particular those interactions which occur when probe antibodies are used to detect adsorbed blood proteins deposited on target particle-modified sensor surfaces. Protein detection analysis was directed toward identification of surface bound human serum albumin, complement factor C3c, and human plasma fibrinogen. Preliminary analysis of generic biomedical surfaces indicated human serum albumin demonstrates a higher binding affinity towards positively charged surfaces (i.e. cysteamine self-assembled monolayer), followed by hydrophobic surfaces. Detection of complement C3c, corresponded with literature, where lower levels were detected on negatively charged surfaces (i.e. mercapto undecanoic acid self-assembled monolayer), and higher levels of more hydrophobic surfaces (i.e. 11-amino undecane thiol self-assembled monolayer). Human plasma fibrinogen was observed to favour hydrophilic over hydrophobic self-assembled monolayer surfaces, which was in accordance with literature. Application of the proposed protein detection method for biocompatibility analysis of target therapeutic molecules, namely metallophthalocyanines and acid functionalised multi-walled carbon nanotubes, demonstrated a dependence on modified-surface film characteristics, such as surface charge and topography with regards to human serum albumin and human plasma fibrinogen analysis representing new insights into their potential biomolecular interactions The highest levels of detected human serum albumin and complement C3c were detected on the GePcSmix-modified surfaces. AlPcSmix-modified surfaces analysis suggested the highest levels of human plasma fibrinogen. Two methods of acid functionalisation were employed, using both nitric and sulphuric acid, and pure nitric acid. A general increase in detected human serum albumin, corresponding with an increase in functionalisation time, was observed. Complement C3c detection suggested an increase in deposited complement C3c, with increasing functionalisation time, when assessing nitric acid functionalised multi-walled carbon nanotubes, and a decrease, with increasing functionalisation time, when assessing nitric and sulphuric acid functionalised multi-walled carbon nanotubes. Analysis of human plasma fibrinogen was inconclusive, as were cytotoxicity experiments utilising MCF-7 cells in the presence of metallophthalocyanine complexes, raising simultaneously important considerations for their application and study. In the first such detailed examination of its kind it was concluded that the proposed method of protein detection, using QCM-D, allows for the rudimentary but rapid means of analysis of select protein corona deposited on particulate biomedical surfaces.
- Full Text:
- Authors: Cromhout, Mary
- Date: 2011
- Subjects: Biomedical materials , Nanostructured materials , Biomedical engineering , Quartz crystal microbalances , Blood proteins , Nanoparticles
- Language: English
- Type: Thesis , Masters , MSc
- Identifier: vital:4102 , http://hdl.handle.net/10962/d1010660
- Description: The biomedical application of nanotechnology has come into the spotlight, with the promise of ‘personalised’ therapeutics that couple early diagnosis with targeted therapeutic activity. Due to the rapid growth of the biomedical applications of nanoparticles, along with the lack of understanding concerning their interactions with biomolecules, there is a pressing need for the development of standard methods directed at investigating the effect of introducing these unique particles into the human body. The central aim of this research is to establish a platform directed at assessing the biological fate of pioneering therapeutic particulate agents, such as metallophthalocyanines (MPcs) and multi-walled carbon nanotubes (FMWCNTs). In particular, we proposed, that Quartz Crystal Microbalance with Dissipation (QCM-D) technology may be employed to assess the composition of blood protein corona deposited on the therapeutic surface, and subsequently assess the biocompatibility of such particles. The proposed method of protein detection utilises the nanogram sensitivity of QCM-D technology to monitor highly specific antibody-antigen interactions. In particular those interactions which occur when probe antibodies are used to detect adsorbed blood proteins deposited on target particle-modified sensor surfaces. Protein detection analysis was directed toward identification of surface bound human serum albumin, complement factor C3c, and human plasma fibrinogen. Preliminary analysis of generic biomedical surfaces indicated human serum albumin demonstrates a higher binding affinity towards positively charged surfaces (i.e. cysteamine self-assembled monolayer), followed by hydrophobic surfaces. Detection of complement C3c, corresponded with literature, where lower levels were detected on negatively charged surfaces (i.e. mercapto undecanoic acid self-assembled monolayer), and higher levels of more hydrophobic surfaces (i.e. 11-amino undecane thiol self-assembled monolayer). Human plasma fibrinogen was observed to favour hydrophilic over hydrophobic self-assembled monolayer surfaces, which was in accordance with literature. Application of the proposed protein detection method for biocompatibility analysis of target therapeutic molecules, namely metallophthalocyanines and acid functionalised multi-walled carbon nanotubes, demonstrated a dependence on modified-surface film characteristics, such as surface charge and topography with regards to human serum albumin and human plasma fibrinogen analysis representing new insights into their potential biomolecular interactions The highest levels of detected human serum albumin and complement C3c were detected on the GePcSmix-modified surfaces. AlPcSmix-modified surfaces analysis suggested the highest levels of human plasma fibrinogen. Two methods of acid functionalisation were employed, using both nitric and sulphuric acid, and pure nitric acid. A general increase in detected human serum albumin, corresponding with an increase in functionalisation time, was observed. Complement C3c detection suggested an increase in deposited complement C3c, with increasing functionalisation time, when assessing nitric acid functionalised multi-walled carbon nanotubes, and a decrease, with increasing functionalisation time, when assessing nitric and sulphuric acid functionalised multi-walled carbon nanotubes. Analysis of human plasma fibrinogen was inconclusive, as were cytotoxicity experiments utilising MCF-7 cells in the presence of metallophthalocyanine complexes, raising simultaneously important considerations for their application and study. In the first such detailed examination of its kind it was concluded that the proposed method of protein detection, using QCM-D, allows for the rudimentary but rapid means of analysis of select protein corona deposited on particulate biomedical surfaces.
- Full Text: